SATO CL408e - Page 218

PN 9001078
Rev. A
Index-2
SATO CL408e/CL412e Service Manual
Index
I
Idle Roller 9-14
IEEE 1284 Parallel Interface 3-4, 8-2
Ignore CR/LF 2-16
Installation Considerations 1-9
Installation Problems, Lan Ethernet Interface 8-5
Interface Options 10-21
Interface Slot 1-3
Interface Specifications 3-1
Interface Types 3-1
L
Label Cutter Kit Installation 9-2
Label Dispenser Kit 9-6
Label Dispenser Installation 9-6
Label Dispenser Latch 9-14
Label Gap Adjustment 4-10
Label Guide 1-5
Label Sensor Assembly 6-25
Label Sensor Module 6-26
Label Sensor Selection 2-5
Label Sensor 1-6, 6-24
Label Taken LED 1-7,1-8
Labels 9-14
Lan Ethernet Interface 8-5
LCD Panel, Advanced Mode 2-13
LCD Printer, Card Mode 2-17
LCD Display Panel 1-7, 1-8
LCD Panel, Normal Mode 2-9
LCD Panel Configuration 2-8
LCD Panel, Clear Non-Standard Protocol 2-37
LCD Panel, Counters Mode 2-32
LCD Panel, Maintenance Mode, Factory Mode 2-35
LCD Panel, Service Mode 2-25
LCD Panel, Firmware Download Mode 2-39
Line Key 1-7, 1-8
M
M8400 Emulation Mode 2-4
Main Circuit Board 6-2
Main PCB Assembly 10-20
MAIN PCB BOARD 9-21
Mechanical Adjustments 5-1
Media Holder 1-5
Mem Select 2-17
Memory Format 2-24
MEMORY MODULE PCB 6-5
MEMORY PCB BOARD 9-16
Mode Selection 2-4
Multi Job Buffer 3-3
N
NetWare Troubleshooting 8-7
O
Offset Label Stop Position Adjustment 4-12
Operation Panel 1-7
Optional Accessories 1-9, 9-1
P
Paper Check Window 1-2
Parity Selection 2-2
PCMCIA Memory Expansion Installation 9-16
PCMCIA Memory Expansion Slot 1-3
PCMCIA Memory Option 10-22
Peel Bar 9-11, 9-13
Physical Characteristics 1- 2
PIN Assignments - IEEE 1284 Cable End 3-5
PIN Assignments - RS232C Printer End 3-6
Pin Assignments 3-11
Pitch Offset Adjustment 2-10
Platen 6-18
Potentiometer Assignments & Adjustments 4-6
Potentiometers 1-7, 1-8
Power Supply 6-9, 6-10
Power Switch 1-3
Print Buffer Hex Dump 8-17
Print Darkness Adjustment 4-16
Print Darkness Setting 2-9
Print Head Alignment Adjustment 5-9
Print Head Assembly 1-4, 10-5
Print Head Balance Adjustment 5-8
Print Head Position Alignment 5-7
Print Head 6-14
Print Mode Selection 2-3
Print Offset 2-14
Print Position Adjustment 4-8
Print Quality Problems 8-11
Print Speed Adjustment 2-10
Printer Features 1-3
Printer Set up 2-3
Priority Setting LCD Command 2-31
Protocol Code Selection 2-4
Protocol Selection 2- 2
Ready/Busy Flow Control 3-8
Real Time Clock Installation 9-26
Receive Buffer Hex Dump 8-17
Receive Buffer Selection 2-3
Receive Buffer 3-3
Removing the Main PCB Board 9-17
Repeat Print via External Signal 2-6
Repeat Print 3-13
Replacement Procedures 6-1
Replacing the Display Panel PCB 6-28
Replacing the Fuses 6-7
Replacing the Head Open Switch 6-27
Replacing the Label Sensor Module 6-26
Replacing the Label Sensor 6-24
Replacing the Main Circuit Board 6-2
Replacing the Platen 6-17
Replacing the Power Supply 6-9
Replacing the Print Head 6-14
Replacing the Ribbon Drive Clutch Washers 6-19