Sharp MX-5000N

MX-5001N SIMULATION 6 – 11
3-3
Purpose
Operation test/check
Function (Purpose)
Used to check the operation of the load in
the finisher and the control circuit.
Section
Finisher
Operation/Procedure
1) Select the item to be operation checked with the touch panel
key.
2) Press [EXECUTE] key.
The selected load performs the operation.
When [EXECUTE] key is pressed, the operation is terminated.
<Inner finisher>
<Saddle stitch finisher>
<4K finisher is installed>
FSWHPD Oscillation guide HP detection
FSWOPD Oscillation guide open detection
FSTPD Staple tray paper detection
FSHPD Staple drive HP detection
FSTHPD Staple shift HP detection
FSD Staple empty detection
FSTD Needle lead edge position detection
FFANLK Fan motor lock detection
FSJOGD Stapler alignment interference detection
FSAD Staple safety SW
FSHTD Shutter open detection
FCD Upper door open detection
FFDD Front cover open detection
F24V 24V output interruption detection
FPSW1 PUSHSW1 detection
FPSW2 PUSHSW2 detection
FPSW3 PUSHSW3 detection
FAED21 Tray 2 area detection 1
FAED22 Tray 2 area detection 2
FAED23 Tray 2 area detection 3
FDSW1 DIPSW1 detection
FDSW2 DIPSW2 detection
FDSW3 DIPSW3 detection
FDSW4 DIPSW4 detection
FDSW5 DIPSW5 detection
FDSW6 DIPSW6 detection
FDSW7 DIPSW7 detection
FDSW8 DIPSW8 detection
FPE Punch motor lock detection
FPUC Punch unit connection detection
FPHPD Punch HP detection
FPSHPD Punch horizontal resist HP detection
FPFDD Punch front door open detection
FPDD Punch dust detection
FPUDSW Punch upper cover open detection SW
FINRPS Entry port reverse pass solenoid
FSLS Paper surface detection solenoid
FPDS Paddle solenoid
FBRS Belt separation solenoid
FRM Registration motor
FSWM Oscillation motor
1
ǂǂǂ6, 08/$7, 21
ǂǂ12
&/26(
7(67
),16(1625&+(&.





3'33'
3'33' 3'&6 )33'
)3$3+6B) )3$3+6B5 )$73'
)*+36
)'73' )3/' )33' )63+6
)673' )6056 )78/'
)7//'
)6/6 )736 )&' )&'
)7/056
)6+6
)66+36 )6('
)66: )&' )666: ))/
)'5+6 )33'
)6$73'
)666:
)3++' )6$3+6 )63*+6 )65+6
)3''
)66+6 )66(6
)66&6
)666+6
FAM Bundle exit paper exit motor
FFJM Alignment motor front
FRJM Alignment motor rear
FSM Staple shift motor
FFSM Staple motor
FTLM Tray lift motor
FFANM Fan motor
FPNM Punch motor
FPSM Punch side resist motor
PDPGS Paper pass paper gate solenoid
PDPTM Paper pass paper transport motor
PDCF Paper pass cooling fan
FPTM1 Paper transport motor 1
FDRLM Finisher paper exit roller lift motor
FGM Gripper motor
FPAM-F Paper alignment motor F
FPAM-R Paper alignment motor R
FSSM Stapler shift motor
FSM Staple motor
FPTM2 Paper transport motor 2
FSDM Saddle motor
FSPTM Saddle paper transport motor
FSPAM Saddle paper alignment motor
FSPM Saddle positioning motor
FSDSM Saddle staple motor
FPHS1 Paper holding solenoid 1
FPHS2 Paper holding solenoid 2
FTLM Tray lift motor
FPM Punch motor
FPSM Punch shift motor
FINRPS Interface paper gate solenoid
FJPM Interface transport motor
FJFM Interface transport fan motor
FFM Entry port transport motor
FAM Bundle paper exit motor
FFJM Alignment motor front
FRJM Alignment motor rear
FSM Staple shift motor
FTLM1 Tray 1 lift motor
FTLM2 Tray 2 lift motor
FFSM Staple motor
FSWM Oscillation motor
FASM Rear edge assist motor
FINRRS Inlet port roller separation solenoid
FBRRS Buffer roller separation solenoid
FFDRRS Paper exit roller separation solenoid
FBES Buffer rear edge holding solenoid
FSHC Shutter open/close clutch
FAORC Bundle exit lower roller clutch
FPNM Punch motor
FPSM Punch horizontal resist motor
1
㩷
㩷
㩷
㩷
㩷
㩷
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
),1/2$'&+(&.


(;(&87(



3'3*6 3'370 )3703'&)
)'5/0 )*0 )3$05)3$0)
)660 )60 )370)7/0
)6'0 )6370 )630)63$0
)6'60 )3+6 )3+6
: Oct. 24 2008
1