EasyManua.ls Logo

Sharp MX-5000N - Page 163

Sharp MX-5000N
524 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
MX-5001N SIMULATION 6 – 16
6-6
Purpose
Operation test/check
Function (Purpose)
Used to check the operation of the fusing
separation.
Section
Fusing
Operation/Procedure
1) Press [FUSER] key to highlight it.
2) Press [EXCUTE] key, and fusing pressure applying and fusing
pressure release are repeated.
During this period, the status of the fusing roller pressure is dis-
played.
7
7-1
Purpose
Setting
Function (Purpose)
Used to set the operating conditions of
aging.
Section
Others
Operation/Procedure
1) Select the target to be set with the touch panel key.
2) Press [EXECUTE] key.
The machine is rebooted in the aging mode.
The aging operation condition set by this mode is maintained here-
after unless the power is turned off or the setting is changed.
7-6
Purpose
Setting
Function (Purpose)
Used to set the operating intermittent aging
cycle.
Section
Operation/Procedure
1) Enter the intermittent aging operation cycle (unit: sec) with 10-
key.
2) Press [OK] key.
The time entered in procedure 1) is set.
* The interval time that can be set is 1 to 900 (sec).
The aging operation condition set by this mode is maintained here-
after unless the power is turned off or the setting is changed.
7-8
Purpose
Operation display
Function (Purpose)
Used to display the warm-up time.
Section
Operation/Procedure
Press [EXECUTE] key.
Counting of the warm-up time is started and the time required for
warm-up is displayed
* Interruption of counting by pressing [EXECUTE] key is inhibited.
PRINT Fusing pressure
applying
Fusing pressure applying Fusing
pressure release (Fusing pressure
applying) The operation is repeated.
FREE Fusing pressure
release
AGING Aging operation setup
INTERVAL Intermittent setup
MISFEED DISABLE JAM detection enable/disable setup
FUSING DISABLE Fusing operation enable/disable setup
WARMUP DISABLE Warm-up skip setup
DV CHECK DISABLE DV unit detection enable/disable setup
SHADING DISABLE Shading disable setup
CCD GAIN FREE No setting of the CCD gain adjustment
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
75$16)(5/2$'&+(&.

326,7,21ǂǂǂǂǂ˖ǂ
(;(&87(7&B57&
ǂǂǂ6,08/$7,21
ǂǂ12
&/26(
7(67
)86(5/2$'&+(&.

(;(&87(
326,7,21ǂǂǂǂǂ˖ǂ

)86(5
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
$*,1*7(676(77,1*

$*,1* ,17(59$/
0,6)(('ǂ',6$%/( )86,1*ǂ',6$%/(
:$5083ǂ',6$%/( '9ǂ&+(&.ǂ',6$%/(
6+$',1*ǂ',6$%/( &&'ǂ*$,1ǂ)5((
(;(&87(
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
,17(59$/$*,1*&<&/(7,0(6(783

$˖
˷˹
˖&<&/(ǂ7,0(˄6(&˅
$˖
2.
ǂǂǂ6,08/$7,21
ǂǂ12
&/26(
7(67
:$50837,0(',63/$<6(77,1*

(;(&87(
6(&21'6

Table of Contents

Other manuals for Sharp MX-5000N

Related product manuals