Sharp MX-5000N

MX-5001N SIMULATION 6 – 15
6
6-1
Purpose
Operation test/check
Function (Purpose)
Used to check the operations of the load in
the paper transport system (clutches and
solenoids) and the control circuits.
Section
Paper transport/Paper exit section
Operation/Procedure
1) Select the item to be operation checked with the touch panel
key.
2) Press [EXECUTE] key.
The selected load performs the operation.
When [EXECUTE] key is pressed, the operation is terminated.
Load operation check method:
The load operation is checked by the operation sound. However,
there are some loads which cannot be checked with the operation
sound.
6-2
Purpose
Operation test/check
Function (Purpose)
Used to check the operations of each fan
motor and its control circuit.
Section
Others
Operation/Procedure
1) Select the item to be operation checked with the touch panel
key.
2) Press [EXECUTE] key.
The selected load performs the operation.
When [EXECUTE] key is pressed, the operation is terminated.
Press [ALL] key to select all the fans collectively.
Load operation check method:
The load operation is checked by the operation sound. However,
there are some loads which cannot be checked with the operation
sound.
6-3
Purpose
Operation test/check
Function (Purpose)
Used to check the operations of the primary
transport unit and the control circuit.
Section
Process (Transport)
Operation/Procedure
1) Press [TC1] or [TC1_R] key to highlight it.
2) Press [EXECUTE] key, and the load operation set in the above
procedure 1) is started.
(Separation operation of BLACK → COLOR → FREE or
BLACK → FREE is repeated.)
[TC1]
[TC1_R]
Section Item/Display Content
Transport/
process
PFM Transport motor
RRM Registration motor
POMF Paper exit motor (normal rotation)
POMR Paper exit motor (reverse rotation)
FUM Fusing motor
CPFM Tray paper feed motor
OSM Shifter motor
CPFC Tray vertical transport clutch
1TURC Primary transport separation clutch
PCSS Process control shutter solenoid
WTNM Waste toner drive motor
PTCHT PTC heater
HPFM Horizontal transport motor
Paper feed CLUM1 Tray 1 lift-up motor
CPUC1 Tray 1 paper feed clutch
CLUM2 Tray 2 lift-up motor
CPUC2 Tray 2 paper feed clutch
MPUC Manual paper feed clutch
MPFS Manual feed take-up solenoid
MPGS Manual paper feed gate solenoid
LSU LSUSS LSU shutter solenoid
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
)(('287387&+(&.


(;(&87(



3)0 550 3205320)
)80 &3)0 &3)&260
785& 3&66 37&+7:710
+3)0 &/80 &/80&38&
&38& 038& 03*603)6
/6866
Item/Display Content
POFM Paper exit cooling fan motor
(POFM_U, POFM_F and POFM_R are simultaneously
ON.)
OZFM Ozone fan motor
PSFM Power cooling fan motor
LSUFM LSU cooling fan motor
CCFM Process cooling fan motor
RCFM Rear cooling fan motor
FUFM Fusing fan motor
PCSFM Toner cooling fan motor
CAFM Cartridge fan motor
MFPFAN Controller fan motor
BLACK Monochrome mode
position
Monochrome mode position → Color
mode position → Non-transport
position → (Monochrome mode
position) The operation is repeated.
COLOR Color mode position
FREE Non-transport
position
BLACK Monochrome mode
position
Monochrome mode position →
Non-transport position →
(Monochrome mode position) The
operation is repeated.
FREE Non-transport
position
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
)$1/2$'6(783

32)0 2=)0
36)0 /68)0
&&)0 5&)0
)8)0 3&6)0
&$)0 0)3)$1
(;(&87(



$//