MX-M260/M310/M260N/M310N SIMULATION 6 - 26
Operation/procedure
The following data are displayed. (The displayed value is the previous
print correction value.)
TARGET = DEV REF+(LIFE-50)+(TH-50)
Developer adjustment value 128, life correction 60 (developer adjust-
ment value plus 10), environment correction 45 (5 subtraction correc-
tion), rapid toner supply correction = 128+(60-50)+(45-50) = 133.)
Operation/procedure
1. Touch the item to be set.
2. Enter the set value with the 10-key.
To support an individual necessity in paper and the environment, it is
variable in the range of 5 to 30uA in the increment of 1uA in each mode.
When changing +V2, check with +V1 unchanged. If there is any trouble
in the half tone image of graphics, keep the relationship between +V1
and +V2 at the default and change it.
When the image quality is deteriorated because the user selects the
OHP mode and use other than the recommended OHP, decrease the
transfer current to adjust deterioration of black background picture qual-
ity. If some of characters are not printed, increase the transfer current.
This setting is changed in linkage with SIM 26-6 destination setting.
*1: SECL/SCA/SEF/EX inch series/EX AB series/EX inch series (FC)/
EX AB series (FC)/China/Taiwan/SEEG2
*2: SEC/SEEG/SUK
36 8573126 - 9430438 (26-sheet model) 1-99 45
37 9430439 - 10287750 (26-sheet model) 1-99 45
38 10287751 - 11145063 (26-sheet model) 1-99 45
39 11145064 - 12002375 (26-sheet model) 1-99 45
40 12002376 - (26-sheet model) 1-99 45
44-17
Purpose
Adjustment/Setup/Operation data output/Check
(Display/Print)
Function
(Purpose)
Used to display the toner density control reference
value.
Section
Image process
(Photoconductor/Developing/Transfer/Cleaning)
Item Operation
TARGET Toner concentration control reference value
DEV REF Developer adjustment value
LIFE Toner container life correction value (SIM 44-16)
TH Toner container environment correction value
44-34
Purpose Setting
Function
(Purpose)
Used to set the transfer current value in each mode.
Item Content
Setting
range
Default
*1 *2
1 +V1F (145)
145mm/s normal paper W
+V1 single surface. Duplex
(Front)
5-30 5
2 +V1R (145)
145mm/s normal paper W
+V1 Duplex (Back)
5-30 5
3 +V2F (145)
145mm/s normal paper W
+V2 single surface. Duplex
(Front)
5-30 18 20
4 +V2R (145)
145mm/s normal paper W
+V2 Duplex (Back)
5-30 14 18
5 +V1S-F (145)
145mm/s normal paper N1
+V1 single surface. Duplex
(Front)
5-30 5
Item
Setting
range
Default
6 +V1S-R (145)
145mm/s normal paper N1
+V1 Duplex (Back)
5-30 5
7 +V2S-F (145)
145mm/s normal paper N1
+V2 single surface. Duplex
(Front)
5-30 22
8 +V2S-R (145)
145mm/s normal paper N1
+V2 Duplex (Back)
5-30 18
9 +V1SS-F (145)
145mm/s normal paper N2
+V1 single surface. Duplex
(Front)
5-30 5
10 +V1SS-R (145)
145mm/s normal paper N2
+V1 Duplex (Back)
5-30 5
11 +V1SS-F (145)
145mm/s normal paper N2
+V2 single surface. Duplex
(Front)
5-30 5
12 +V1SS-R (145)
145mm/s normal paper N2
+V2 Duplex (Back)
5-30 5
13 +V1 THICK (145)
145mm/s thick paper > LTR
+V1
5-30 5
14 +V2 THICK (145)
145mm/s thick paper > LTR
+V2
5-30 14
15
+V1 THICK S
(145)
145mm/s thick paper t LTR
+V1
5-30 5
16
+V2 THICK S
(145)
145mm/s thick paper t LTR
+V2
5-30 18
17 +V1 THIN (145)
145mm/s thin paper > LTR
+V1
5-30 5
18 +V2 THIN (145)
145mm/s thin paper > LTR
+V2
5-30 18
19 +V1 THIN S (145)
145mm/s thin paper t LTR
+V1
5-30 5
20 +V2 THIN S (145)
145mm/s thin paper t LTR
+V2
5-30 18
21 +V1 LABEL (145)
145mm/s label paper > LTR
+V1
5-30 5
22 +V2 LABEL (145)
145mm/s label paper > LTR
+V2
5-30 18
23
+V1 LABEL S
(145)
145mm/s label paper t LT R
+V1
5-30 5
24
+V2 LABEL S
(145)
145mm/s label paper t LT R
+V2
5-30 18
25 +V1 OHP (145) 145mm/s OHP > LTR +V1 5-30 5
26 +V2 OHP(145) 145mm/s OHP > LTR +V2 5-30 14
27 +V1 OHP S (145) 145mm/s OHP t LTR +V1 5-30 5
28 +V2 OHP S (145) 145mm/s OHP t LTR +V2 5-30 18
29
+V1 POSTCARD
(145)
145mm/s postcard/envelope
> 100mm +V1
5-30 5
30
+V2 POSTCARD
(145)
145mm/s postcard/envelope
> 100mm +V2
5-30 26
31
+V1 POSTCARD
S (145)
145mm/s postcard/envelope
t 100mm +V1
5-30 5
32
+V2 POSTCARD
S (145)
145mm/s postcard/envelope
t 100mm +V2
5-30 26
33 +V1F (122)
122mm/s normal paper W
+V1 single surface. Duplex
(Front)
5-30 5
34 +V1R (122)
122mm/s normal paper W
+V1 Duplex (Back)
5-30 5
35 +V2F (122)
122mm/s normal paper W
+V2 single surface. Duplex
(Front)
5-30 12 14
36 +V2R (122)
122mm/s normal paper W
+V2 Duplex (Back)
5-30 10
37 +V1S-F (122)
122mm/s normal paper N1
+V1 single surface. Duplex
(Front)
5-30 5
38 +V1S-R (122)
122mm/s normal paper N1
+V1 Duplex (Back)
5-30 5
Item Content
Setting
range
Default
*1 *2
To Next Page
Loading...
