Sharp XV-Z2000 User Manual

-63
Appendix
Specifications
Product type
Model
Video system
Display method
DLP panel
Lens
Projection lamp
Video input signal
S-video input signal
Component input signal
(INPUT 1, 2)
Analog RGB/Digital
(INPUT 5/DIGITAL)
Horizontal resolution
Pixel clock
Vertical frequency
Horizontal frequency
Computer control signal
Rated voltage
Input current
Rated frequency
Power consumption
Power consumption (standby)
Heat dissipation
Operating temperature
Storage temperature
Cabinet
I/R carrier frequency
Dimensions (approx.)
Weight (approx.)
Supplied accessories
Replacement parts
Projector
XV-Z2000
PAL/PAL 60/PAL-M/PAL-N/SECAM/NTSC 3.58/NTSC 4.43
DTV 480I/480P/720P/1080I
Single Panel Digital Micromirror Device (DMD™) by Texas Instruments
Panel size: 0.8"
Drive method: Digital Light Processing (DLP™)
No. of dots: 921,600 dots (1,280 [H] × 720 [V])
1–1.5 × zoom lens, F2.0–2.5 f=21.3–31.6 mm
275 W DC lamp
RCA Connector: VIDEO (INPUT 4), composite video, 1.0 Vp-p, sync negative, 75 Ω
terminated
4-pin Mini DIN connector (INPUT 3)
Y (luminance signal): 1.0 Vp-p, sync negative, 75 Ω terminated
C (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminated
RCA Connector
Y: 1.0 Vp-p, sync negative, 75 Ω terminated
PB (CB): 0.7 Vp-p, 75 Ω terminated
PR (CR): 0.7 Vp-p, 75 Ω terminated
29-pin DVI-I terminal
<Digital>
Input impedance 50 Ω
Input level 250-1000 mV
<Analog>
Input impedance 75 Ω
Input level 0.7 Vp-p
Y: 1.0 Vp-p, sync negative, 75 Ω terminated
PB (CB): 0.7 Vp-p, 75 Ω terminated
PR (CR): 0.7 Vp-p, 75 Ω terminated
<Synchronization signal>
••
••
• Separate sync/Composite sync
Input level TTL level
Input impedance 1 KΩ
••
••
• Green on sync
Input level (Synchronizing input) 0.286 Vp-p
Input impedance 75 Ω
720 TV lines (DTV 720P input)
12–80 MHz
43–75 Hz
15–70 kHz
9-pin D-sub connector (RS-232C Port)
AC 100–240 V (HONG KONG: 220 V)
3.65 A (When using AC 100 V)/(HONG KONG: 1.6 A)
50/60 Hz (HONG KONG: 50 Hz)
360 W (When using AC 100 V)/(HONG KONG: 345 W)
6 W (When using AC 100 V)
1,350 BTU/hour
+5°C to +35°C
–20°C to +60°C
Plastic
38 kHz
310 (W) × 89 (H) × 282 (D) mm
4.3 kg
Remote control, Two AA size batteries, Power cord, 21 pin RCA conversion adaptor,
Video cable, Lens cap (attached on the body), Operation manual
Lamp unit (Lamp/cage module) (AN-K2LP), Remote control (RRMCGA334WJSA), AA
size batteries, Power cord for Europe except U.K. (QACCVA011WJPZ), Power cord for
U.K., Hong Kong and Singapore (QACCBA036WJPZ), Power cord for Australia and New
Zealand (QACCLA018WJPZ), 21 pin RCA conversion adaptor (QSOCZ0361CEZZ),
Video cable (QCNWGA001WJZZ), Lens cap (PCAPHA021WJSA), Operation manuals;
for European 7 languages (TINS-B530WJZZ) / for Chinese and Korean (TINS-
B531WJZZ)
As a part of policy of continuous improvement, SHARP reserves the right to make design
and specification changes for product improvement without prior notice. The performance
specification figures indicated are nominal values of production units. There may be some
deviations from these values in individual units.
XV-Z2000E_E_P62_66.p65 2004.10.21, 1:14 PM63

Sharp XV-Z2000 Specifications

General

Projection distance	2.6 - 3.9 m
Contrast ratio (typical)	2500:1
Screen size compatibility	40 - 200 \
Projector native resolution	SXGA (1280x1024)
Lamp type	SHP
Lamp power	275 W
Light source type	Lamp
Service life of light source	3000 h
Video in	XGA, Mac 19” (in intelligent compression), SVGA/VGA, Mac 16”/13”
I/O ports	2x component, 1x RCA video, 1x S-video, DVI-I (analogue component, digital & analogue RGB) x 1
Dimensions (WxDxH)	310 x 287 x 104 mm
Power requirements	100-240V AC, 50/60Hz
Power consumption (typical)	360 W
Market positioning	Home cinema

Weight and Dimensions

Weight	4300 g