How to fix system error on Shimano Steps Bicycle Accessories?
If you experience a system error with your Shimano Steps Bicycle Accessories, ensure the cable is properly connected and not loose. If the problem persists, it's recommended to contact the place of purchase.
Why is the gear position not displayed on my Shimano Steps Bicycle Accessories?
If the gear position is not displayed on your Shimano Steps Bicycle Accessories, it is only displayed when the electronic gear shifting unit is installed. Check if the electric wire connector is disconnected. If you are not sure, contact the place of purchase.
General| Brand | Shimano Steps |
|---|---|
| Model | SW-E6010 |
| Category | Switch |
| Language | English |
Contact the place of purchase or a bicycle dealer for information on installation and adjustment.
Be sure to read this user's manual thoroughly before use, and follow them for correct use.
Do not deform, modify, disassemble or apply solder directly to the battery. Doing so may cause leakage.
Do not give too much attention to the cycle computer display while riding, otherwise accidents may result.
Be sure to remove the battery and charging cable before wiring or attaching parts to the bicycle.
Periodically clean the chain using an appropriate chain cleaner. Do not use alkaline or acidic cleaning agents.
Precautions for battery placement, avoiding sunlight, and storage.
Guidelines for disposing of batteries outside the European Union.
Connect to PC using E-TUBE PROJECT for customization and firmware updates.
Connect via Bluetooth LE using E-TUBE PROJECT for customization and firmware updates.
Highlights features like lightweight design, silent ride, and shifting performance.
Describes available assist modes: HIGH, NORM, ECO, OFF, and WALK.
Instructions for charging different battery types before first use.
Procedure to turn the system power on and off.
Guide on how to select and change assist modes using the cycle computer or switch unit.
Diagrams and labels identifying all system components.
Details operating temperatures, voltage, power, and other technical data.
Important steps before using the battery, including charging.
Explains the meaning of the LED indicators on the battery charger.
Describes how battery LED lamps indicate charging progress and status.
How to check the current battery charge level using the power button LEDs.
Guidelines for charging, storage, and managing battery deterioration.
Step-by-step instructions for securely installing the battery.
Procedures for safely removing the battery from its mount.
How to attach the cycle computer to its bracket.
How to detach the cycle computer from its bracket.
Details on powering the system on and off via cycle computer or battery.
Operation of the EW-EN100 unit, including LED indicators and basic functions.
Overview of controls for SC-E6100/SW-E6010 and SC-E7000/SW-E7000.
Explains the functions of left/right assist switches and cycle computer buttons.
Describes the functions of the EW-EN100 junction unit.
How to control the bicycle's lights using the system controls.
Explains the various elements shown on the SC-E6100 display.
How the EW-EN100 indicates the battery charge level.
How the SC-E6100/SC-E7000 displays battery charge level.
Using Assist-X/Y to select or change assist modes.
Using the EW-EN100 button to cycle through assist modes.
Procedure to activate the WALK assist mode.
How to start, stop, and exit the walk assist mode.
How to cycle through different travel data metrics on the SC-E6100.
How to reset traveling distance, time, average, and maximum speed.
How to change displayed travel data on the SC-E7000.
How to change between automatic and manual gear shifting.
Steps to access the setting menu from the basic screen.
Steps to access the setting menu from the basic screen for SC-E7000.
Resets traveling distance and other setting values.
Procedure to set the current time on the system.
Configure the preferred start gear for the start mode function.
Configure the display backlight mode (ON, OFF, MANUAL).
Adjust the display brightness level from 1 to 5.
Configure the battery-powered light to be always on or always off.
Enable or disable the system's beep sounds.
Select the unit of measurement between kilometers and miles.
Choose the display language from a list of available options.
Select the font color for the display, choosing between black and white.
Adjust the rear shifting unit for electronic gear shifting; contact dealer for details.
Adjust the automatic shift timing to influence pedaling effort.
Enable or disable shifting advice during manual shifting mode.
Reset the RD protection function after a significant impact.
Exit the current setting menu and return to the main screen.
Perform RD protection reset using the EW-EN100 button and LED indicators.
Adjust gear shifting for electronic units; contact dealer.
Information on automatic data backup and updating via E-TUBE PROJECT.
Connect to PC/tablet for configuration and firmware updates using E-TUBE PROJECT.
Details about ANT and Bluetooth LE connections for wireless system communication.
Interprets LED patterns for system, temperature, security, and charging errors.
Lists error codes (W011, W013, W032) and their corresponding remedies.
Actions to take when an error message appears on the screen.
Comprehensive list of system error codes and their solutions.
How EW-EN100 LEDs indicate errors, requiring power off and dealer consultation.
Solves issues related to assistance not being provided or short traveling distance.
Addresses problems causing stiff pedaling.
Covers battery quick discharge, recharging problems, and overheating.
Troubleshooting for charger warmth, LED illumination, and battery insertion/removal.
Diagnosis for when front or tail lights do not illuminate.
Resolves problems with cycle computer display, startup, gear position, and settings.
Addresses issues with switch operation, beeps, and gear shifting sounds.
Solutions for weakened assistance, rear wheel noise, and start mode gear shifting.
A space to record the key number for purchasing spare keys.
To Next Page
