Siemens Optipoint 420 User Manual (English)

Other manuals for Siemens Optipoint 420

Administration Guide125 pages

Quick Reference6 pages

Questions and Answers:

B
Brittany JordanAug 27, 2025
What to do if my Siemens Optipoint 420 Telephone shows 'Feature not avail.'?
- C
  Courtney RojasAug 27, 2025
  If your Siemens Telephone displays 'Feature not avail.', 'Incorrect entry', or 'Key not programmed', it indicates that a speed dial number is not available, an appointment was entered incorrectly, the entry is blocked or not allowed, a prerequisite has not been fulfilled, or the number dialed was incomplete. Correct your input, select a permitted option, or enter the phone number in full.
C
christophersmithAug 28, 2025
How to fix 'Base n lashes' error on Siemens Optipoint 420 Telephone?
- D
  Daniel BensonAug 28, 2025
  If your Siemens Telephone displays the line "Base n" lashes, it could be due to several reasons: * The handset is not registered - register the handset. * The handset is outside the base radio range or the radio signals are too weak - move closer to the base or change your position. * The intervals between synchronization attempts are too long - switch the handset off and then back on again.
D
Daniel BurkeAug 28, 2025
Why does my Siemens Optipoint 420 say 'no access'?
- C
  Christopher JohnsonAug 28, 2025
  If your Siemens Telephone displays 'no access', it means a blocked function was called. You must apply to the relevant service personnel for the COS for the blocked function.
W
William HollandAug 29, 2025
What to do if my Siemens Optipoint 420 shows 'Denied'?
- J
  Julie StevensAug 29, 2025
  If your Siemens Telephone displays 'Denied', it means an incorrect PIN was entered. Enter the correct PIN to proceed.
Q
qjacksonAug 25, 2025
What to do if the line 'Base n' flashes on my Siemens IP Phone?
- A
  Antonio CraigAug 25, 2025
  If your Siemens IP Phone displays 'Base n' flashing, it indicates the handset is likely out of the base radio range, the radio signals are too weak, the handset isn't registered, or synchronization attempts are too spaced out. Try moving closer to the base, changing your position, registering the handset, or switching the handset off and on again.
J
josephharrellAug 30, 2025
Why does my Siemens Optipoint 420 say 'protected'?
- R
  Richard WilsonAug 30, 2025
  If your Siemens Telephone displays 'protected', it indicates that data transfer is active. Wait and try again later.
Z
zwongAug 30, 2025
How to fix no display on Siemens Optipoint 420?
- M
  Mary LiAug 30, 2025
  If there is no display on your Siemens Telephone, the battery pack might be flat. Press the On-hook key until you receive confirmation. Charge or replace the battery pack.
R
Robert SpencerAug 31, 2025
What to do if Siemens Optipoint 420 key-stroke doesn't work?
- K
  Kara StewartAug 31, 2025
  If your Siemens Telephone does not react to key-strokes, the keypad lock may be activated. Press the hash key until you receive confirmation, then release the key.
R
Ricky WatsonAug 31, 2025
What does de-crescendo tone sequence mean on Siemens Optipoint 420?
- C
  Courtney SimpsonAug 31, 2025
  If you hear a de-crescendo tone sequence during input on your Siemens Telephone, it indicates an incorrect entry was made. Repeat the key sequence while watching the display, and consult the operating manual where applicable.
W
williamslisaSep 1, 2025
How to enable ringer on my Siemens IP Phone?
- K
  Karen CurtisSep 1, 2025
  If your Siemens IP Phone isn't ringing, the ringtone might be deactivated, or the 'Do Not Disturb' feature could be active. To resolve this, activate the ringer and deactivate 'Do Not Disturb'.