Why is the time and date still wrong on my Siemens Industrial PC after setting it in BIOS?
If the time and date are still incorrect on your Siemens Industrial PC even after setting them in the BIOS, the backup battery is likely dead. You should replace the backup battery.
Why is my Siemens Industrial PC not turning on?
Your Siemens Industrial PC might not be operational due to a lack of power supply or because it's being operated outside of its specified ambient conditions. First, check the power supply, power cord, and power plug, ensuring the On/Off switch is in the correct position. Also, verify the ambient conditions are within the device's specifications. If the device was recently transported in cold weather, allow it to sit for approximately 12 hours before turning it on.
What to do if my Siemens Industrial PC monitor remains dark?
If your Siemens Industrial PC monitor remains dark, there are several possible reasons. First, make sure the monitor is switched on and not in 'power save' mode by pressing any key on the keyboard. Also, check the brightness setting on the monitor and increase it if it's set too low. Finally, verify that the power cord is properly connected to both the monitor and the power outlet, and that the monitor cable is securely connected to both the system unit and the monitor.
How to fix Siemens Industrial PC mouse pointer not showing?
If the mouse pointer is not appearing on the screen of your Siemens Industrial PC, it could be due to the mouse driver not being loaded or the mouse not being properly connected. Check whether the mouse driver is correctly installed and available when you start the user program. Also, ensure the mouse cord is properly connected to the system unit and check any adapters or extensions you might be using.
How to troubleshoot a non-responsive USB device on Siemens Industrial PC?
If a USB device is not responding on your Siemens Industrial PC, the USB ports may not be correctly supported. Try turning on USB Legacy Support for mouse and keyboard in the BIOS settings. For other devices, ensure you have the correct USB device drivers installed for your operating system.
How to correct the wrong time and date on my Siemens Industrial PC?
To correct the wrong time and date on your Siemens Industrial PC, open the BIOS Setup and set the correct time and date.
What to do if 'Windows boot manager failed' appears on my Siemens Industrial PC?
If you see the pop-up message 'Windows boot manager failed' when installing the operating system on your Siemens Industrial PC, it could be because the M.2 NVMe/SATA SSD card is changed to another boot device. Press Enter to continue the boot. Alternatively, the M.2 NVMe/SATA SSD card may have lost the boot image or is broken. In this case, reinstall the operating system or change to another M.2 NVMe/SATA SSD card.
How to fix 1000M full duplex mode not running at full speed on Siemens Industrial PC?
If the 1000M full duplex mode cannot run at full speed on all onboard LAN ports of your Siemens Industrial PC, it might be due to Time Coordinated Computing resulting in Giga Band Ethernet workloads. To resolve this, open the firmware selection menu, select 'Setup Utility' > 'Power' > 'Advanced CPU Control' > 'C-States', and change its value from 'Enabled' to 'Disable'.
How to display software completely on Siemens IPC277G 7" panels?
If some software application and OS windows cannot be displayed completely on your Siemens IPC277G 7" panels, it is likely because the resolution of the device is less than 600 pixels. You can use the WinMove function in the SIMATIC IPC PDT tool to address this issue.
How to resolve Ethernet port bridge connection error on Siemens Industrial PC?
To resolve an Ethernet port bridge connection error while the bridge function is enabled on your Siemens Industrial PC, right-click the Windows Start menu and select 'Device Manager' > 'Network adapters' > 'Interl EC* *GbE Connection' > 'Properties' > 'Advanced' > 'Promiscuous Mode', and change its value to 'Enabled'.
Details the SIMATIC IPC277G's features, design, and configuration options.
Covers essential safety precautions, system expansions, and battery handling.
Provides guidance on securing the device against cyber threats.
Covers checking delivery, identifying the device, and preparing mounting.
Provides instructions for mounting the device using clips or VESA adapters.
Details device connection, protective earth, power supply, and network setup.
Provides essential requirements and steps for initial device commissioning.
Explains the procedure for powering the device on and off.
Detailed guide on installing M.2 modules into the device.
Procedure for installing and removing M.2 NVMe or SATA SSDs.
Guidelines for carrying out repairs and handling electrostatic sensitive devices.
Covers replacing the backup battery and memory modules.
Offers tips for locating and resolving common device problems.
General| Type | Panel PC |
|---|---|
| Series | SIMATIC IPC277G |
| Mounting | Panel mount |
| Operating System | Windows 10 IoT Enterprise |
| Protection Class | IP65 (front) |
| Interfaces | Ethernet, USB, Serial |
| Storage | SSD (Solid State Drive) |
| Operating Temperature | 0 °C to 50 °C |
| Processor | Intel Celeron or Intel Core i3/i5 |
To Next Page