Siemens SINUMERIK 808D - Page 162

808d-mte40 5 0., 0., 0., 0., 0., 0., 0.,
0., 0., 0., 0., 0., 0., 0.,
0., 0., ...
0. 1. 1/1 M
808d-mte60 5 0., 0., 0., 0., 0., 0., 0.,
0., 0., 0., 0., 0., 0., 0.,
0., 0., ...
0. 1. 1/1 M
Description: Smoothing of the programmed block end points with compressor type COMPCAD. Value 0: no
smoothing. Value 1: maximum smoothing.
Entry for all dynamic G code groups.
20487 COMPRESS_SMOOTH_FACTOR_2 EXP, C05 B1
- Smoothing by compressor DOUBLE NEW CONF
-
808d-me42 5 0., 0., 0., 0., 0., 0., 0.,
0., 0., 0., 0., 0., 0., 0.,
0., 0., ...
0. 1. 1/1 M
808d-me62 5 0., 0., 0.5, 0.5, 0.5 0. 1. 1/1 M
808d-te42 5 0., 0., 0., 0., 0., 0., 0.,
0., 0., 0., 0., 0., 0., 0.,
0., 0., ...
0. 1. 1/1 M
808d-te62 5 0., 0., 0., 0., 0., 0., 0.,
0., 0., 0., 0., 0., 0., 0.,
0., 0., ...
0. 1. 1/1 M
808d-mte40 5 0., 0., 0., 0., 0., 0., 0.,
0., 0., 0., 0., 0., 0., 0.,
0., 0., ...
0. 1. 1/1 M
808d-mte60 5 0., 0., 0., 0., 0., 0., 0.,
0., 0., 0., 0., 0., 0., 0.,
0., 0., ...
0. 1. 1/1 M
Description: Extent to which the programmed block end points are smoothed in the case of compressor
type COMPCAD for
non-geometry axes. Value 0: No smoothing. Value 1: Maximum smoothing.
Entry for each dynamic G code group.
20488 SPLINE_MODE EXP B1
- Setting for spline interpolation BYTE NEW CONF
-
- - 0, 0, 0, 0, 0, 0, 0, 0... 0 0x7 3/3 M
Description: This MD is used to determine the settings for spline interpolation. The allocation of
the spline segments to the NC blocks can thus be influenced. With spline
interpolation,
the
spline
blocks are combined, if possible, in such a way, that there
are no blocks that are too short and could lead to a reduction in the possible path
velocity.
Bit 0: With BSPLINE, blocks that are too short are avoided.
Bit 1: With BSPLINE/ORICURVE, blocks that are too short are avoided.
Bit 2: With CSPLINE, blocks that are too short are avoided.
20490 IGNORE_OVL_FACTOR_FOR_ADIS EXP B1
- G64x independent of overload factor BOOLEAN NEW CONF
-
808d-me42 - FALSE, FALSE,
FALSE, FALSE,
FALSE, FALSE,
FALSE, FALSE...
0 - 1/1 M
808d-me62 - TRUE 0 - 1/1 M
Machine data
3.3 Channel-specific machine data
Parameter Manual
162 List Manual, 01/2017