1x: At the machining G codes, G601 (fine positioning window) becomes active
independent of the programmed exact stop condition.
2x: At the machining G codes, G602 (coarse positioning window) becomes active
independent of the programmed exact stop condition.
3x: At the machining G codes, G603 (setpoint value reached) becomes active
independent of the programmed exact stop condition.
The values of the units digits and tens digits are added.
For example, the value of EXACT_POS_MODE = 2 means that the exact stop condition G602
is
always activated
automatically at G00, independently of which exact stop condition
was programmed. At all other G codes of group 1, the programmed exact stop condition
becomes active.
20552 EXACT_POS_MODE_G0_TO_G1 EXP B1
- Exact stop condition at G00-G01 transition BYTE NEW CONF
-
- - 0, 0, 0, 0, 0, 0, 0, 0... 0 5 2/2 M
Description: Configuration of a stop at transition from G00 to a different G code of the 1st G code
group, and also vice versa, at transition from non-G00 to G00 in continuous-path mode.
In exact-stop mode, the positioning window programmed or set in MD20550
$MC_EXACT_POS_MODE is used.
The following applies:
0: No additional stop, no control of exact stop
1: Behavior active as with G601 (positioning window, fine).
2: Behavior active as with G602 (positioning window, coarse).
3: Behavior active as with G603 (setpoint reached).
4: As 0,
in addition, the override of the subsequent non-G00 block is taken into account in the
G00 block via LookAhead in the case of a change from G00 to non-G00.
5: As 0,
in addition, the override of the subsequent block is taken into account via LookAhead
in the case of a change from G00 to non-G00 and non-G00 to G00.
20560 G0_TOLERANCE_FACTOR EXP B1
- Tolerance factor for G00 DOUBLE NEW CONF
-
808d-me42 - 1.0, 1.0, 1.0, 1.0, 1.0,
1.0, 1.0, 1.0...
1.e-9 - 1/1 M
808d-me62 - 3.0 1.e-9 - 1/1 M
808d-te42 - 1.0, 1.0, 1.0, 1.0, 1.0,
1.0, 1.0, 1.0...
1.e-9 - 1/1 M
808d-te62 - 1.0, 1.0, 1.0, 1.0, 1.0,
1.0, 1.0, 1.0...
1.e-9 - 1/1 M
808d-mte40 - 1.0, 1.0, 1.0, 1.0, 1.0,
1.0, 1.0, 1.0...
1.e-9 - 1/1 M
808d-mte60 - 1.0, 1.0, 1.0, 1.0, 1.0,
1.0, 1.0, 1.0...
1.e-9 - 1/1 M
Description: Tolerance factor for G00.
This factor is used to make different settings for the tolerances for processing when
G00 is active (rapid traverse, infeed motion).
This tolerance factor is relevant for the following control functions:
1. Compressor (COMPCAD, COMPCURV, and COMPON)
2. Smoothing with G64x
Machine data
3.3 Channel-specific machine data
Parameter Manual
164 List Manual, 01/2017
To Next Page
Loading...
