Siemens SIWAREX WP251 - Page 5

Table of contents
SIWAREX WP251
Manual, 12/2015, A5E37203357A
5
8.2.3 Operating mode NAWI (non-automatic weighing instrument) - Removal ............................... 59
8.2.4 Operating mode AWI (automatic weighing instruments) ........................................................ 59
8.2.5 Operating mode ACI (automatic catchweighing instruments) - Filling .................................... 60
8.2.6 Operating mode ACI (automatic catchweighing instruments) - Removal ............................... 61
8.3 DR 3 Calibration parameters .................................................................................................. 61
8.3.1 Overview ................................................................................................................................. 61
8.3.2 Scale name ............................................................................................................................. 66
8.3.3 Unit of weight .......................................................................................................................... 66
8.3.4 Gross identifier ........................................................................................................................ 66
8.3.5 Code for regulations................................................................................................................ 67
8.3.6 Minimum weighing range ........................................................................................................ 67
8.3.7 Maximum weighing range ....................................................................................................... 67
8.3.8 Calibration weights 0, 1, 2 and calibration digits 0, 1, 2 ......................................................... 67
8.3.9 Scale interval .......................................................................................................................... 68
8.3.10 Zero by power-on .................................................................................................................... 68
8.3.11 Zero by power-on when tare ≠ 0 ............................................................................................. 68
8.3.12 Automatic zero adjustment ..................................................................................................... 68
8.3.13 Subtractive / additive tare device ............................................................................................ 69
8.3.14 Weight simulation allowed ...................................................................................................... 69
8.3.15 Automatic zero tracking .......................................................................................................... 69
8.3.16 Maximum tare load ................................................................................................................. 70
8.3.17 Maximum negative zero setting limit (power-on) .................................................................... 70
8.3.18 Maximum positive zero setting limit (power-on) .....................................................................
70
8.
3.19 Maximum negative zero setting limit (semi-automatically) ..................................................... 70
8.3.20 Maximum positive zero setting limit (semi-automatically) ....................................................... 71
8.3.21 Standstill monitoring ................................................................................................................ 71
8.3.22 Standstill 1 - range .................................................................................................................. 72
8.3.23 Standstill 1 - time .................................................................................................................... 72
8.3.24 Max. waiting time for standstill 1 ............................................................................................. 72
8.3.25 Standstill 2 - range .................................................................................................................. 73
8.3.26 Standstill 2 - time .................................................................................................................... 73
8.3.27 Setting time before standstill 2 ................................................................................................ 73
8.3.28 Frequency low pass filter 1 ..................................................................................................... 74
8.3.29 Order no. low pass filter 1 ....................................................................................................... 74
8.3.30 Depth average filter ................................................................................................................. 74
8.3.31 Weighing operating mode ....................................................................................................... 75
8.3.32 SecureDisplay including weighing range data ........................................................................ 75
8.3.33 SecureDisplay interface .......................................................................................................... 75
8.3.34 SecureDisplay version ............................................................................................................ 75
8.3.35 Smallest zoom factor of SecureDisplay .................................................................................. 75
8.3.36 Grid frequency ........................................................................................................................ 75
8.4 Calibration ............................................................................................................................... 76
8.4.1 Calibration with calibration weights ......................................................................................... 76
8.4.2 Automatic calibration............................................................................................................... 78
8.5 DR 4 Output of calculated calibration digits ............................................................................
79
8.
5.1 Overview ................................................................................................................................. 79
8.
5.2 Calibration digits 0, 1, 2 (calculated) ....................................................................................... 80
8.6 DR 5 Tare / zero memory ....................................................................................................... 80
8.6.1 Overview ................................................................................................................................. 80
8.6.2 Effective tare weight - from specification 1, 2 or 3 .................................................................. 81