GW2145 - GW1160 - GW4060 - GW4190
CONTENTS
1 INTRODUCTION ................................................................................................................................................... 6
1.1 GW FAMILY - INTENDED USE .............................................................................................................................. 7
1.2 DEFINTITION: “RESPONSIBLE AUTHORITY” IN RELATION TO THE DEVICE .......................................................... 7
1.3 WASHING TROLLEYS AND ACCESSORIES ............................................................................................................. 8
1.3.1 Smeg WD-PRINTE printer – GW2145, GW1160, GW4060 series ................................................................ 8
1.3.2 Smeg WD-PRINT9 Printer – GW4190 Series .............................................................................................. 8
1.4 PERISTALTIC PUMP P3 (NOT INSTALLABLE ON GW2145) ................................................................................... 9
1.5 LIST OF MODELS ................................................................................................................................................ 10
2 KEY TO THE SYMBOLS USED IN THE MANUAL AND ON THE APPLIANCE .............................................................11
3 GENERAL WARNINGS .........................................................................................................................................12
3.1 ACCESSING AND REUSING THE DEVICE AFTER AN INCOMPLETE CYCLE ........................................................... 13
3.2 DOOR OPENING ................................................................................................................................................ 14
3.3 MANUAL DOOR RELEASE PROCEDURE ............................................................................................................. 15
3.4 GW4190 OPENING THE DOOR OF THE SIDE CABINET - SERIES GW4190 ONLY ................................................ 15
4 DESCRIPTION OF CONTROLS AND PROGRAMS ...................................................................................................17
4.1 CONTROLS ......................................................................................................................................................... 17
4.2 CONTROLS - DETAILED DESCRIPTION ............................................................................................................... 18
4.2.1 A0 PARAMETER DISPLAY ........................................................................................................................... 19
4.3 INDICATOR LEDS - INTRODUCTION ................................................................................................................... 20
4.4 INDICATOR LEDS - DETAILED EXPLANATION ..................................................................................................... 21
4.5 SELECTING THE WASHING PROGRAMME ......................................................................................................... 23
4.6 BRIEF TABLE OF THE PROGRAMS INSTALLED.................................................................................................... 25
4.6.1 RESINS - SOFTENER, REGENERATION AND WASHING PHASE ................................................................... 26
4.6.2 DRYING PHASE – Only for GW4060, GW4190 series ................................................................................ 26
4.6.3 CUSTOM PROGRAMS ................................................................................................................................ 28
4.7 A0 THERMAL DISINFECTION PARAMETER ........................................................................................................ 29
4.8 PREPARING THE LOAD FOR WASHING AND DISINFECTION .............................................................................. 30
4.9 END OF CYCLE ................................................................................................................................................... 31
4.10 INTERRUPTING A PROGRAM IN EXECUTION .................................................................................................... 32
4.11 PROGRAM SPECIAL OPTIONS ............................................................................................................................ 33
4.11.1 DELAYED START - Setting the hours .......................................................................................................... 33
4.11.2 DELAYED START - Starting the program and display ................................................................................. 33
4.11.3 TEMPORARY DISABLING OF DEMI WATER ................................................................................................ 34
4.11.4 Deleting “Delayed start” - “No Demi” settings ......................................................................................... 35
4.12 RESET PROCEDURE............................................................................................................................................ 36
4.13 PRINTING THE CYCLE AND APPLIANCE PARAMETERS ....................................................................................... 37
5 SETUP MODE - “FUNCTIONS” .............................................................................................................................37
5.1 ACCESSING THE SETUP MODE / ENTERING THE PASSWORD ........................................................................... 38
5.2 ACCESS AND PARAMETER MODIFICATION ....................................................................................................... 39
5.3 “SET“ PARAMETERS .......................................................................................................................................... 41
5.3.1 APPLIANCE DATA STORAGE, OVERWRITING, “Set -b” .............................................................................. 44
5.4 “CLOC” – DATE AND TIME PARAMETERS .......................................................................................................... 46
5.5 SETTING THE “PrEn” “PROGRAM ENABLING” FUNCTION................................................................................. 46
6 INSTALLATION INSTRUCTIONS ...........................................................................................................................49
6.1 USE OF THE WATER SOFTENER ......................................................................................................................... 49
6.2 USING DETERGENT AND NEUTRALISING AGENT .............................................................................................. 50
6.2.1 LIQUID DETERGENT INTAKE SYSTEM ........................................................................................................ 50
6.2.2 DETERGENT LEVEL SENSORS - OPTIONAL ................................................................................................. 52
To Next Page
Loading...
