STR-DA5500ES
156
D-VIDEO BOARD IC3610 MB91F644PMC-GE1 (VIDEO SYSTEM CONTROLLER)
Pin No. Pin Name I/O Description
1 VSS - Ground terminal
2 C - External capacitor connection terminal
3, 4 TX_INT1, TX INT2 I Interrupt signal input from the HDMI transmitter
5 UC3V SDA I/O
Two-way I2C data bus with the HDMI receiver, HDMI transmitter and D/A converter (for video
section)
6 NO_USE - Not used
7 UC3V SCL O
I2C clock signal output to the HDMI receiver, HDMI transmitter and D/A converter (for video
section)
8 to 11 NO_USE - Not used
12 TX RST1 O Reset signal output to the HDMI transmitter “L”: reset
13 TX 5VPWR1 O
Power supply on/off control signal output terminal for HDMI OUT A connector
“H”: power on
14 TX RST2 O Reset signal output to the HDMI transmitter “L”: reset
15 TX 5VPWR2 O
Power supply on/off control signal output terminal for HDMI OUT B connector
“H”: power on
16 RX RST O Reset signal output to the HDMI receiver “L”: reset
17, 18 NO_USE - Not used
19 1444_OEB O Output enable signal output to the HDMI input selector
20 to 22
1444_SELA to
1444_SELC
O HDMI input selection signal output to the HDMI input selector
23 to 27 NO_USE - Not used
28, 29 +5V_SELA, +5V_SELB O HDMI +5V power input selection signal output terminal
30 to 32 NO_USE - Not used
33 VSS - Ground terminal
34 VCC - Power supply terminal (+3.3V)
35 to 38 NO_USE - Not used
39 INIT I Reset signal input from the system controller “L”: reset
40 MD0 I Writing mode selection signal input from the system controller
41 MD1 I Writing mode selection signal input terminal Fixed at “L” in this set
42 XO I System clock input terminal (4 MHz)
43 XI O System clock output terminal (4 MHz)
44 VSS - Ground terminal
45 NON LPCM O Non-LPCM setting signal output terminal “H”: non-LPCM
46 AUDIO MUTE REQ O Audio muting request signal output to the system controller, DSP1 and DSP2
47 CEC SEL O CEC line selection signal output terminal
48 RX INT I Interrupt signal input from the HDMI receiver
49 to 51 NO_USE - Not used
52 ENDFLAG O Writing end fl ag output to the system controller “H”: end
53 Flash Update Tx O Serial data output to the RS232C connector
54 Flash Update Rx I Serial data input from the RS232C connector
55 NO_USE - Not used
56 YAMAHA INT_N I Interrupt signal input from the OSD controller
57 to 63 NO_USE - Not used
64 AVCC - Power supply terminal (+3.3V)
65 AVRH I Reference voltage (+3.3V) input terminal
66 AVSS - Ground terminal
67 YAMAHA RESET O Reset signal output to the fl ash memory and OSD controller “L”: reset
68, 69 NO_USE - Not used
70
Faroudjia UCOM
RESET
O Reset signal output to the video processor and fl ash memory "L": reset
71
Faroudjia Power
DETECT
I Power detection signal input from the video processor
72 Faroudjia UCOM BUSY I Busy signal input from the video processor
73 MAIN_Faro_Wake O Wake-up signal output to the video processor
74 NO_USE - Not used
75
2nd Faroudjia UCOM
RESET
O Reset signal output terminal Not used
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
To Next Page
Loading...
