Sony VPL-EX145 - Default Chapter; Table of Contents

1 (E)
VPL-EX100
Table of Contents
Manual Structure
Purpose of this manual ............................................................ 3 (E)
Related manuals ...................................................................... 3 (E)
1. Service Overview
1-1. Appearance Figure ....................................................1-1 (E)
1-2. Board Locations ........................................................1-1 (E)
1-3. Disassembly ..............................................................1-2 (E)
1-3-1. Upper Case Assembly ......................................1-2 (E)
1-3-2. Rear Panel ........................................................1-4 (E)
1-3-3. Main Board ......................................................1-5 (E)
1-3-4. G Board ............................................................1-6 (E)
1-3-5. DC Fan (Lamp Duct) .......................................1-7 (E)
1-3-6. Speaker.............................................................1-8 (E)
1-3-7. Optical Block ...................................................1-9 (E)
1-3-8. DC Fan (Intake) .............................................1-10 (E)
1-3-9. Power Supply (Ballast) .................................. 1-11 (E)
1-3-10. Front Panel Assembly and NFTA Board ........1-12 (E)
1-3-11. DC Fan (Exhaust) and U Board ..................... 1-13 (E)
1-3-12. Lens Assembly and
S Prism Block Assembly ...............................1-14 (E)
1-3-13. S Out-polarizer (G)/(B) Assembly and
S Out-pre-polarizer (R)/(G)/(B) Assembly ....1-16 (E)
1-3-14. S In-polarizer (R)/(G)/(B) Assembly ............. 1-18 (E)
1-3-15. S PS Assembly ...............................................1-20 (E)
1-4. Optional Fixtures .....................................................1-21 (E)
1-4-1. Extension Boards and Extension Cables .......1-21 (E)
1-4-2. Connection .....................................................1-22 (E)
1-5. Service Mode (Network Volume)
(VPL-EX145/EX175)..............................................1-23 (E)
1-5-1. Outline ...........................................................1-23 (E)
1-5-2. Update Function .............................................1-23 (E)
1-5-3. Event Trace Function .....................................1-26 (E)
1-5-4. Setup Function ...............................................1-29 (E)
1-6. Indicator Display ..................................................... 1-30 (E)
1-7. Lead-free Solder ...................................................... 1-31 (E)
2. Adjustments
2-1. Service Know-How ...................................................2-1 (E)
2-1-1. When the S Prism Block Assembly is
Replaced...........................................................2-1 (E)
2-1-2. When Replacing the Main Board.....................2-1 (E)
2-2. Mechanical Adjustment ............................................. 2-2 (E)
2-2-1. Polarizer Adjustment........................................2-2 (E)
2-3. Electrical Adjustment ................................................2-3 (E)
2-3-1. Required Equipment ........................................2-3 (E)
2-3-2. How to Enter the Service Mode .......................2-3 (E)
2-3-3. V COM Adjustment .........................................2-3 (E)
2-3-4. Angle Detect Sensor Adjustment .....................2-4 (E)
2-4. Software Update ........................................................2-4 (E)
2-4-1. Preparation .......................................................2-4 (E)
2-4-2. Main (Scan Converter).....................................2-6 (E)
2-4-3. Sub ................................................................... 2-8 (E)
2-4-4. Ext (Network) ..................................................2-9 (E)
2-5. Quick Access ...........................................................2-10 (E)
2-5-1. Preparation .....................................................2-10 (E)
2-5-2. Saving of 3Dgamma/LookUpTable/
Main Board Data ............................................2-10 (E)
2-5-3. Saving of DDC Data ...................................... 2-11 (E)
2-5-4. Saving of NVM Data .....................................2-12 (E)
2-5-5. Writing of 3Dgamma/LookUpTable/
Main Board Data ............................................2-13 (E)
2-5-6. Writing of DDC Data .....................................2-14 (E)
2-5-7. Saving of NVM Data .....................................2-15 (E)
2-6. Adjustment Item Initialize Data ..............................2-16 (E)
3. Troubleshooting and Circuit Description
3-1. Troubleshooting.........................................................3-1 (E)
3-2. Circuit Description ....................................................3-5 (E)
3-2-1. Main Board ......................................................3-5 (E)
3-2-2. Sensor Board ....................................................3-6 (E)
3-2-3. G Board ............................................................3-6 (E)