To Next PageTo Next Page
Need help?Do you have a question about the Spirent C1 and is the answer not in the manual?
General| Model | C1 |
|---|---|
| Category | Network Hardware |
| Manufacturer | Spirent |
| Type | Network Tester |
| Ports | Multiple Ethernet ports |
| Protocols Supported | Ethernet, TCP/IP, UDP |
| Operating Temperature | 0°C to 40°C |
| Storage Temperature | -20°C to 70°C |
Instructions for examining the product carton and contents for damage upon receipt.
Details compliance with FCC Rules for Class A digital devices and operational conditions.
Indicates compliance with EU EMC and Low Voltage Directives, meeting specific technical standards.
Explains the WEEE label and encourages proper disposal and recycling of electronic equipment.
Specifies appliance requirements, customer-supplied cables, and minimum PC specifications.
Explains network connection requirements, including the administrative port and its use.
Describes the physical connector panels and necessary cabling for SPT-C1 and SPT-C2.
Illustrates the connector panel for the SPT-C1 2 x 10GbE model and details network data cables.
Shows connector panels for SPT-C1 4x1GbE NICs (NIC-33, NIC-32) and specifies required cables.
Details the connector panel for SPT-C1 4 x BroadR-Reach (NIC-43) and cable pinouts.
Illustrates connector panels for SPT-C1 with WAVE-1 WiFi modules and specifies cable connections.
Depicts the connector panel for SPT-C1 10G/5G/2.5G/1G/100M NIC and associated network cables.
Shows connector panel for SPT-C1 with WAVE-2 WiFi and details copper and RF cable connections.
Illustrates the connector panel for SPT-C2 8x10G/5G/2.5G/1G/100M (Dual NIC-63) and specifies network data cables.
Details connector panels for SPT-C2 WiFi models, covering ports and cable types for different NICs.
Diagrams physical port layout for SPT-C2 NIC-70-V2, showing frequency assignments.
Details the power button location and power cord socket for SPT-C1 and SPT-C2 appliances.
Provides instructions on powering the appliance on/off and notes typical boot times.
Recommends installing the SPT-C2 in a dust-free, dry environment with adequate airflow and power.
Offers guidance on rack mounting, including ambient temperature, airflow, mechanical loading, and earthing.
Outlines steps to connect to the appliance's GUI, including IP configuration and cable connections.
Shows images of SPT-C1 administrative ports for different model revisions.
Identifies the administrative port on the SPT-C2 appliance.
Details methods for configuring IP settings via local connection or SSH for SPT-C1 and SPT-C2.
Details the login process and commands for configuring network settings via CLI.
Explains the use of RJ-45 connectors for interconnecting multiple Spirent chassis for synchronization.
Describes ETR connectors (Serial DCE, 10MHz, 1PPS SMA) used for time reference connections.
Lists pin assignments for the External Time Reference Serial DCE (RJ-45) connector.
Lists pin assignments for the External Time Reference 10MHz and 1 PPS SMA connectors.
Lists pin assignments for the 1588 (RJ-45) connector, detailing TXRX signals.
Explains how to check active and standby Spirent TestCenter versions using the command line.
Details the process of switching between installed firmware versions using the command line interface.
Describes the AutoFallBack feature, which reverts to a previous version upon upgrade failure.
Shows how the active Spirent TestCenter version is displayed in the admin prompt.
Provides instructions for enabling, disabling, and resetting the appliance password protection.
Lists administrative commands for Spirent C1/C2 with descriptions.
Continues the list of administrative commands for Spirent C1/C2, covering network and system functions.
Lists related documentation including Quick Reference, Release Notes, and Knowledge Base access.
Provides contact details and hours for technical support across different global regions.
Provides the main company website and corporate address for Spirent Communications.
