Super Products Camel 1200 (Ejector Unloading) - User Manual

What to do if there is no main hydraulic oil pressure in Super Products Trucks?

Same questionReply

• D

  daniel55Aug 18, 2025

  To address the issue of no main hydraulic oil pressure in your Super Products Truck, first ensure that work mode is enabled and the truck is not in road mode. Next, check if the hydraulic pump is engaged, and verify that the transfer case has shifted out of road mode. Also, make sure the hydraulic supply valve is open and that the hydraulic reservoir has an adequate oil level, checking for any leaks. Finally, verify the air solenoid is receiving a signal; if not, consult Table 7-2: Electrical Troubleshooting.

  

  Reply

How to fix engine RPM if it will not increase or decrease in Super Products Trucks?

Same questionReply

• C

  Chelsea NormanAug 23, 2025

  If the engine RPM will not increase or decrease on your Super Products Truck, turn the engine speed dial back to zero and then turn it back up.

  

  Reply

What to do if the emergency stop message is displayed on the front control panel HMI screen of Super Products Trucks?

Same questionReply

• D

  Devon ArellanoAug 26, 2025

  To resolve the emergency stop message displayed on the front control panel HMI screen of your Super Products Truck, replace the wireless pendant batteries.

  

  Reply

What to do if the engine starts but all functions will not operate on Super Products Trucks?

Same questionReply

• E

  Emma CookAug 28, 2025

  If the engine starts but all functions do not operate on your Super Products Truck, reset the emergency stop switch by twisting the knob. This issue happens when the emergency stop switch is pushed at the front panel or curbside panel.

  

  Reply

Why vacuum pump does not draw vacuum on Super Products Trucks?

Same questionReply

• B

  Barbara PageAug 30, 2025

  If the vacuum pump on your Super Products Truck does not draw vacuum, first enable WORK and VAC modes and verify that the transfer case has shifted. Next, shift the transmission into D drive. Also, ensure the vacuum relief door is closed, the float ball is free and clean, the intake hose is not restricted or plugged, and the filter is clean or replaced.

  

  Reply

Why is the hydraulic oil foamy or milky in Super Products Trucks?

Same questionReply

• B

  Bonnie GentrySep 2, 2025

  If the hydraulic oil in your Super Products Truck is foamy or milky, inspect the suction hose and fittings from the hydraulic oil tank to the pump for any air leaks. If there is water in the oil: * Drain all oil in system and replace oil and oil filter. * Inspect or replace hydraulic reservoir fill cap.

  

  Reply

How to fix tailgate if it will not close on Super Products Trucks?

Same questionReply

• S

  Stacie HendersonSep 4, 2025

  To fix the issue where the tailgate will not close on your Super Products Truck, set the MODE rocker switch on the control panel to DUMP. This is because the front or curbside panel MODE rocker switch is not set to DUMP.

  

  Reply

Why does the vent door open and engine RPM drops to idle on Super Products Trucks?

Same questionReply

• I

  ijacobsonSep 7, 2025

  If the vent door opens and the engine RPM drops to idle on your Super Products Truck, clear emergency stop mode by resetting the emergency stop button – turn the pendant OFF then back to ON and then all the way to SHIFT. This happens when the pendant emergency stop button is depressed.

  

  Reply

What to do if the chassis air pressure is too low in Super Products Trucks?

Same questionReply

• M

  Matthew BarrySep 9, 2025

  If the chassis air pressure is too low on your Super Products Truck, run the engine until the air pressure reaches 100 psi. This is caused by the transfer case not engaging.

  

  Reply

How to restore water pressure on Super Products Trucks?

Same questionReply

• B

  Brandon OdomSep 12, 2025

  If there is no water pressure on your Super Products Truck, turn the water pressure knob down to zero and then back up. This issue is caused by the water pressure knob being left turned up.

  

  Reply