Need help?Do you have a question about the Sutron Satlink 3 and is the answer not in the manual?
General| Weight | 1.5 lbs (0.68 kg) |
|---|---|
| Communication Protocols | GOES, Iridium |
| Operating Temperature | -40 to 60°C |
| Data Logging | Yes |
| Power Source | External DC power |
| Modulation | BPSK (GOES), QPSK (Iridium) |
| Data Interface | RS-232 |
| Enclosure Rating | NEMA 4X |
Lists model numbers and their corresponding descriptions for Satlink units and optional modems.
Details the components and features included with the SL3-1 satellite transmitter.
Details the components and features included with the SL3-SDI-1 satellite transmitter.
Details the components and features included with the SL3-XMTR-1 satellite transmitter.
Explains safety symbols used in the manual and their meanings for safe operation.
Introduces the three available Satlink 3 models: SL3-1, SL3-SDI-1, and SL3-XMTR-1.
Describes the main components like multi-function buttons, LEDs, and connectivity ports.
Details site requirements for installation and mounting procedures for SL3-1 and SL3-SDI-1/XMTR-1.
Explains proper earth ground connection and how to connect GOES/METEOSAT/INSAT antennas.
Guides on connecting GPS antennas, power supply, and various sensor types like SDI-12 and analog.
Details on connecting wind sensors, digital outputs, and other interface types.
Instructions for connecting external modems for remote communication.
Covers installation procedures for both mobile and PC versions of the LinkComm software.
Explains how to connect to Satlink via USB, Wi-Fi, modem, or serial connection.
Overview of LinkComm's interface, including Dashboard, Measurements, Data, Telemetry, and GPS tabs.
Details on using the Diagnostics tab for firmware, LinkComm status, and terminal access.
Guides on creating new stations, importing setups, and managing connections.
Covers testing, examining, calibrating, and configuring sensors and measurements.
Explains how to download log data and use USB drives for data transfer.
Details on viewing status, software versions, setting time, and system maintenance.
Provides essential steps to secure the Satlink station, including physical access and Wi-Fi.
Details on setting up password protection, access tiers, and protection levels.
Covers sensor activation, templates, measure types, labels, units, and other sensor parameters.
Details on setting measurement intervals, times, averaging, sampling, and results.
Explains various measurement types like SDI-12, Analog, Wind, Digital, Meta, and Battery.
Covers slope, offset, equation processing, and alarm configuration for measurements.
Configures logging intervals, error values, and transmission data content settings.
Details on setting up scheduled transmissions, including schedule and TX format.
Covers Iridium setup, global settings, and message handling for Iridium communication.
Explains cell modem setup, global settings, listening modes, and SMS transmission.
Provides details on monitoring telemetry status, including antenna aiming and radio diagnostics.
Details on configuring the Satlink's Wi-Fi hotspot for local access.
Explains how to configure and control digital outputs (DOUT) based on alarms or manual settings.
Covers cutoff settings for voltage and temperature to prevent operation outside safe ranges.
Explains Iridium module functionality, including messages and data retrieval.
Covers cellular modem capabilities for communication, data delivery, and remote access.
Describes methods for retrieving data lost due to transmission failures.
Instructions for downloading log data via LinkComm or USB and understanding log formats.
Explains how events are logged and how timestamps are applied to measurements and transmissions.
Guides on clearing errors, viewing status, and understanding measurement and system error types.
Details common measurement errors like sensor failure and interval issues.
Describes system errors such as recording off, time not set, battery low, and transmission failures.
Explains Pseudobinary B, C, and D formats used for data transmission.
Details Six Bit Binary, SMS, SHEF, SHEFFIX, CSV, and ASCII formats.
Covers TCP/IP sessions, telemetry headers, and packet structures for communication.
Details on RS232 connection and configuring Satlink for logger communication.
Explains how to transmit data using EXTBUF commands and manage the transmission buffer.
Explains the benefits and interface of using command line for Satlink interaction.
Covers essential commands for checking status, setup, measurements, and logging.
Provides a detailed list of available commands and their descriptions for system control.
Introduces the SDI-12 standard, its advantages, and wiring guidelines.
Explains how to set up SDI sensors, manage addresses, and use useful SDI commands.
Details the warranty terms for Sutron-manufactured equipment.
Outlines the procedures and turnaround times for equipment repair and return.
Lists regulatory compliance information for NESDIS, Eumetsat, INSAT, CE, and Wi-Fi modules.
Details FCC and Industry Canada compliance statements for Iridium and Cellular modems.
To Next Page