Why is my Tally Dascom Printer printing too light or too dark?
If your Tally Dascom printer's output is too light or too dark, ensure the ribbon cartridge is properly installed and feeds smoothly. If the issue persists, replace the ribbon. Also, verify that the print gap lever is correctly set for your paper's thickness.
What to do if my Tally Dascom Printer smears and stains the page?
If your Tally Dascom printer is smearing or staining the page, take the following steps: * Ensure the print gap lever is set correctly for the paper thickness. * Check the ribbon for wear and replace if needed. * Inspect the print head for dirt and clean with a soft cloth if necessary. * If the issue continues, the print head may need replacement.
What to do if my Tally Dascom 1140 Printer is on but it will not print?
If your Tally Dascom printer is on but not printing, ensure the Online indicator is lit. Check that the interface cable is securely connected to both the printer and the computer. Also, confirm that paper is loaded. Run the printer Status Page. If printing executes normally, the problem is caused by the interface, the computer, incorrect printer settings, or incorrect software settings. Ensure the printer driver selected in your software matches the emulation selected on the printer.
What to do if my Tally Dascom 1140 is printing erratic or wrong characters?
If your Tally Dascom printer is printing erratically or outputting wrong characters, ensure the interface cable is securely connected to both the printer and computer. Verify that the printer driver selected in your software matches the emulation selected on the printer. Check the length of the interface cable (Maximum Parallel & USB: 2 meters, Serial: 15 meters). Try using another interface cable.
Why Tally Dascom 1140 Printer paper jams while printing?
If your Tally Dascom printer is experiencing paper jams during printing, turn off the printer and carefully remove the jammed paper. Clear any obstructions from the paper path. Ensure that the Print Gap lever is correctly set for the thickness of your paper. For continuous forms, ensure the incoming and outgoing paper stacks are correctly placed so paper feeds straight.
Why Tally Dascom 1140 paper cannot be loaded or fed?
If paper cannot be loaded or fed into your Tally Dascom printer, make sure the paper select lever on the top right of the printer is set correctly. Also, ensure that the paper covers the paper-out sensor.
Why Tally Dascom 1140 paper jams while loading?
If your Tally Dascom printer is jamming paper during loading, turn off the printer and remove the jammed paper. Clear any obstructions from the paper path. Make sure the Print Gap lever is set for the thickness of your paper. Ensure the paper is not folded, creased, or torn. For continuous forms, ensure that the left and right tractors are set so the forms are stretched taut.
What to do if my Tally Dascom Printer page is blank?
If your Tally Dascom printer is producing blank pages, ensure that the ribbon cartridge is properly installed. Also, make sure the gap lever is set correctly.
Why Tally Dascom 1140 paper slips off the forms tractors?
If the paper slips off the forms tractors or the perforated holes tear during printing with your Tally Dascom printer, ensure that the forms tractors are positioned correctly for the width of your paper and that the perforated holes of the paper fit directly over the tractor pins.
Why Tally Dascom 1140 power does not turn on?
If your Tally Dascom printer is not powering on, check whether the mains voltage is correct. Ensure the power cord is securely connected to both the printer and the mains power outlet. Make sure the power outlet is functional; if not, use another outlet. Turn the power off, wait a minute, and then turn the printer on again. If the printer still has no power, contact your dealer.
Step-by-step instructions for installing the printer ribbon cartridge.
How to connect the printer to a computer using an interface cable.
Steps for connecting the printer to a power source and checking voltage.
Guide for installing the necessary printer driver software on a Windows system.
Configuration options for system-level settings like language and emulation.
Settings related to paper handling, length, margins, and loading.
Parameters for printing on forms with pre-printed black marks.
Steps to reset printer settings to their original factory defaults.
Common print quality issues and their corresponding solutions.
Troubleshooting steps for common paper loading and jamming issues.
Solutions for common issues related to printer operation and power.
Interpreting error messages indicated by the printer's LED lights.
General| Type | Dot Matrix Printer |
|---|---|
| Connectivity | Parallel, Serial, USB |
| Print Resolution | 360 x 360 dpi |
| Paper Handling | Continuous forms, Cut sheets |
| Paper Path | Rear |
| Number of Pins | 24-pin |
To Next Page
