What does OPBFT High Pressure Fault mean on my TECO Inverter and how to fix it?
If your TECO Inverter displays an OPBFT High Pressure Fault, you can try the following: Check if the feedback signal is correct and with the proper connection. Check if the feedback value of pressure is lower than the limit of minimum pressure (23-12).
What to do if my TECO Inverter displays FBLSS PID Feedback Signal Loss?
If your TECO Inverter displays FBLSS PID Feedback Signal Loss, you can try the following: Check if the proportion of loss pressure (23-19) is set correctly. Make sure the feedback sensor is installed correctly and the PID feedback signal operates normally.
What does EF1 External Fault(S1) mean on my TECO Inverter and how to fix it?
If your TECO Inverter is showing an EF1 External Fault(S1) error, you should: Check if the multi-function input function is set incorrectly. Also, check the wiring.
What does TOL External Overload mean on my TECO E510s Inverter and how to fix it?
If your TECO Inverter displays TOL External Overload, you can try the following: Check the reason for the external fault. Reset the digital input terminal of external overload.
What to do if my TECO E510s shows OC over current?
If your TECO Inverter displays an OC over current error, you can try the following: Extend the acceleration or deceleration time. Also, check the motor wiring. If the problem persists, disconnect the motor and try running the inverter.
What does CE communication error mean on my TECO E510s and how to fix it?
If your TECO Inverter is showing a CE communication error, you should: Check the connection. Also, check the host computer and software.
What does OT Over torque detection mean on my TECO E510s Inverter and how to fix it?
If your TECO Inverter displays an OT Over torque detection error, you can try the following: Check the over torque detection parameters (08-15 / 08-16). Also, check and reduce the motor load, and check the operation duty cycle.
What does OH4 Motor overheat mean on my TECO Inverter and how to fix it?
If your TECO Inverter is showing an OH4 Motor overheat error, you should: Check the surrounding temperature of the motor. Also, check that the MT and GND terminal wiring is correct.
What to do if my TECO E510s Inverter displays IPL input phase loss?
If your TECO Inverter displays an IPL input phase loss error, you can try the following: Check the input wiring and tighten the screws. Also, check the power supply.
What does OPL output phase loss mean on my TECO E510s Inverter and how to fix it?
If your TECO Inverter is showing an OPL output phase loss error, you should: Check the output wiring and tighten the screws. Also, check the motor and inverter rating.
General| Storage Temperature | -20°C to +60°C |
|---|---|
| Enclosure Rating | IP20 |
| Series | E510s |
| Input Voltage | 3-phase 380-480V AC |
| Power Range | 0.4kW~22kW |
| Overload Capacity | 150% for 60 seconds |
| Braking Unit | Built-in or external (optional) |
| Protection Features | Over-voltage, Over-current, Under-voltage, Over-heat, Short-circuit |
| Communication Interfaces | RS-485 (Modbus RTU) |
| Operating Temperature | -10°C to +50°C |
| Humidity | 5% to 95% RH, non-condensing |
| Cooling Method | Forced air cooling |
Introduction to the inverter manual and contact information for support.
Safety guidelines before applying power to the inverter.
Safety guidelines during the power-up sequence of the inverter.
Safety checks and procedures to perform before operating the inverter.
Safety guidelines to follow while the inverter is operating.
Procedures for safe maintenance, inspection, and replacement of inverter parts.
Guidelines for the proper and safe disposal of the inverter unit.
Explanation of the information provided on the inverter's nameplate.
Details on how to identify the specific model and series of the inverter.
Technical specifications for standard product models of the inverter.
Recommended environmental conditions for inverter installation and operation.
Guidelines and methods for installing the inverter correctly.
Instructions and best practices for wiring power and control circuits.
Detailed description of the inverter's keypad, displays, and functions.
Overview of parameter groups and their organization within the inverter.
Detailed explanation of individual parameters and their functions.
Information on the inverter's integrated PLC functionality and ladder logic.
General information and overview of fault detection mechanisms.
Common troubleshooting steps and checks for general inverter issues.
Detailed troubleshooting procedures for specific inverter faults and errors.
Checklist for routine and periodic inspections to ensure stable inverter operation.
Instructions for performing regular maintenance tasks on the inverter.
Specifications for external reactors used with the inverter.
Selection and specifications for electromagnetic contactors and circuit breakers.
Recommended fuse types and ratings for inverter protection.
UL recommended fuse specifications for inverter models.
Specifications and selection guide for braking resistors.
Information on input noise filters for suppressing electrical noise.
List and specifications of available accessories for the inverter.
General safety precautions and warnings for UL certified products.
Warnings related to fire hazards due to improper installation or connections.
Information regarding UL/cUL certification and compliance standards.
Conditions for maintaining UL compliance when using the drive with other equipment.
Overview of basic parameters for inverter configuration.
Parameters related to Volts/Hertz (V/F) control mode.
Parameters for configuring external digital inputs and outputs.
Parameters related to inverter start, stop, and fault reset functions.
Parameters for inverter protection functions like overload and stall prevention.
Parameters for configuring the Proportional-Integral-Derivative (PID) control.
Details on communication connection methods and data frame formats.
Diagrams illustrating network connection configurations for Modbus.
Memory map for the E510s inverter's built-in PLC function.
Instructions for operating the PLC function, including RUN/STOP and memory clear.
Model number and technical specifications for the JN5-CM-USB.
Pin definitions for the USB interface cable connection.
Notes on accessory models, descriptions, and specifications.
Introduction to the E510s Safe Torque Off (STO) function.
Overview of safety directives and standards applicable to the STO function.
Explanation of the E510s Safe Torque Off (STO) feature and its safety functions.
Details on terminal layouts and interface connections for the inverter.
Explanation of safety input logic levels and status indicators.
Truth table for safety-related signals and input/output status.
Safety design principles and specifications for the 11-301 series.
To Next Page
