Texecom Premier 888 - Arming and Disarming Areas; To Arm Areas; To Part Arm Areas

P
rem
i
er
888
&
8168
U
ser
M
anua
l
Th
e
A
rm
i
ng
M
enu
INS177 11
Arming and Disarming Areas
An area is Armed, when ALL zones within that area are ON
(not omitted).
An area is Part Armed, when SOME zones within that area
are ON (not omitted) and some zones within that area are
OFF (omitted).
!
An area is only Part Armed when zones are omitted
using the ‘Part Arm 1, 2 or 3’ procedure.
Omitting zones manually (see page 15 for details) is
not classed as Part Arming.
To Arm Areas
➤ To arm areas, proceed as follows:
Ensure that the premises are secure (all doors and
windows closed etc.) and the Ready light is on.
To do a quick arm, press
%
%%
%
.
Or
Enter a valid User code
....
........
....
, the display
should look like this:
!"#$"%#&'()#)"
*+,#-$-).,/
Press
%
%%
%
, the display will look something like this:
A.@.> )#*+.'- #X
##X#W WWWWW99 #\
Use keys
!
!!
!
-
1
11
1
to select/deselect areas i.e.
!
and
0
= Areas A and B, the display will look something like
this:
A.@.> )#*+.'- #X
##X#* UWWWW99 #\
!
Only areas that exist on the system can be selected.
(A ‘Star’ means the area can be selected and a ‘Dot’
means the area cannot be selected).
Pressing
2
will select/deselect all areas.
Pressing
%
will toggle between areas A to H and
I to P (Premier 8168 only).
When all the required areas have been selected press
#
##
#
, the exit tone will sound (if silent arm has not been
selected) and the display will look something like this:
*+.'-#1 (#IJ1) #X
####*U9 99999#
Leave the premises, when the system has armed, the exit
tone (if sounding) will stop.
The selected areas are now armed.
To Part Arm Areas
➤ To part arm areas, proceed as follows:
Ensure that the premises are secure (all windows and doors
not being omitted are closed) and the Ready light is on.
To do a quick part arm, press
'
''
'
.
Or
Enter a valid User code
....
........
....
, the display
should look like this:
!"#$"%#&'()#)"
*+,#-$-).,/
Press
)
))
)
until the display looks like this:
!"#$"%#&'()#)"
0'+)#*+,#-$-).,/
Press
%
%%
%
, the display will look something like this:
A.@.> )#*+.'- #X
##X#W WWWWW99 #\
Use keys
!
!!
!
-
1
11
1
to select/deselect areas i.e.
!
,
0
and
*
= Areas A, B and C, the display will look
something like this:
A.@.> )#*+.'- #X
##X#* UBWWW99 #\
!
Only areas that exist on the system can be selected.
A ‘Star’ means the area can be selected and a ‘Dot’
means the area cannot be selected.
Pressing
2
will select/deselect all areas.
Pressing
%
will toggle between areas A to H and
I to P (Premier 8168 only).
When all the required areas have been selected press
#
##
#
, the display will look something like this:
*+.'-#1 (#IJ1) #X
####*UB 99999#
Leave the protected area. When the areas have armed,
the exit tone (if sounding) will stop and the display will look
something like this
*+.'-#A )'$#*+ ,.<
####*UB 99999
W##0*QM#*QKI!##W
#M%.#54#K'+#7553
The selected areas are now part armed.