Texecom Premier 888 - Omit 24 Hr Zones; Reinstate 24 Hr Zones; Set Chime Areas; Turning Chime on and View Act. Faults

Th
e
A
rm
i
ng
M
enu
P
rem
i
er
888
&
8168
U
ser
M
anua
l
16 INS177
Omit 24Hr Zones
It is possible to exclude (omit) or include 24Hr zones whilst
the system is disarmed to allow access to an area. Users
with access to this function can only omit zones that have
been programmed as ‘Omittable’.
➤ To omit 24Hr zones, proceed as follows:
Enter a valid User code
....
........
....
, the display
should look like this:
!"#$"%#&'()#)"
*+,#-$-).,/
Press
)
))
)
until the display looks like this:
!"#$"%# &'()#) "
D,1)#78 E+#F"( .-
Press
#
##
#
, the display will look something like this:
F"(.#55 3#A.>% +.
?+"()#! ""+### ##X
Enter a zone number
...
......
...
or use the
)
))
)
key
to search, the display will look something like this:
F"(.#53 :#A.>% +.
U'>O#!" "+#### ##X
!
If the zone can be omitted, there will be a ‘Star’ to
the right of the zone number. Only zones that have
the ‘Omit’ attribute assigned to them can be omitted.
Press
3
33
3
to omit the selected zone, the display will look
something like this:
F"(.W53 :#A.>% +.
1-#D,1)).<
F"(.W53 :#A.>% +.
U'>O#!" "+#### ##X
!
A ‘Star’ will appear to the left of the zone number to
indicate that the zone has been selected for omitting.
Repeat for other zones.
When all the required zones have been selected for omitting
press
/
//
/
, the display should look like this:
!"#$"%#&'()#)"
IJ1)#K.(%/
Press
#
##
#
, the display will look something like this:
W#F"(.-#D,1)).<#W
#M%.#54#K'+#7553
The selected 24Hr zones are now omitted.
Reinstate 24Hr Zones
To reinstate the omitted zones, simply follow the instructions
again. However, when the
3
key is pressed, the display will
look something like this:
F"(.W53 :#A.>% +.
1-#_")# D,1)). <
F"(.W53 :#A.>% +.
U'>O#!" "+#### ##X
Set Chime Areas
When a zone is enabled for Chime the Keypad will
generate a Chime tone every time the zone is activated.
Users with access to this function will be able to turn
Chime on and off for selected areas.
Zones within an area can be individually programmed for
chime in Edit Chime Zones (see page 23 for details).
➤ To set Chime areas, proceed as follows:
Enter a valid User code
....
........
....
, the display
should look like this:
!"#$"%#&'()#)"
*+,#-$-).,/
Press
&
&&
&
, the display will look something like this:
I('P@.# BC1,.# "(
##X#WWW 99999# \
Use keys
!
!!
!
-
1
11
1
to select/deselect areas i.e.
!
,
0
and
*
= Areas A, B and C, the display will look
something like this:
I('P@.#BC1,.#"(
##X#*UB99999#\
!
Only areas that have been programmed for ‘Chime’
can be selected. A ‘Star’ means the area can be
selected and a ‘Dot’ means the area cannot be
selected.
Pressing
2
will select/deselect all areas.
Pressing
%
will toggle between areas A to H and
I to P (Premier 8168 only).
When all the required areas have been selected for
‘Chime’ press
#
##
#
, the display should look like this:
!"#$"%# &'()#) "
A.)#BC1 ,.#*+. '-/
Press
(
((
(
to exit the menu and return to normal.
Turning Chime On and Off
The display will normally show the time & date.
##0+.,1 .+#234 2
3868495 8N#M%. #54
➤ To turn Chime On, proceed as follows:
Press
&
&&
&
, the keypad will chime to indicate that Chime
is now enabled.
➤ To turn Chime Off, proceed as follows:
Press
&
&&
&
, the keypad will bleep to indicate that Chime is
now disabled.