Texecom Premier 888 - Quick Arm Keys; Quick Arm; Quick Part; Reset and Service Messages

P
rem
i
er
888
&
8168
I
ns
t
a
ll
a
ti
on
M
anua
l
O
pera
ti
ng
th
e
Al
arm
S
ys
t
em
INS177 7
Quick Arm Keys
The ‘Quick’ keys allow the system to be armed without
having to enter a User code first.
!
The ‘Quick’ keys will only work if the keypad has
been programmed to allow arming in this way.
Quick Arm
To arm the system, press
%
%%
%
.
!
All areas that the keypad being used is assigned to
will now Arm.
Quick Part Arm
To part arm the system, press
'
''
'
.
!
All areas that the keypad being used is assigned to
will now Part Arm.
Reset and Service Messages
When the system requires attention because of a potential
problem, the display will show one of three service
messages. These messages can also be accessed at any
time, allowing the user to view installer information.
!
These messages would normally be programmed
with the telephone numbers of the installer or the
Alarm Receiving Centre.
➤ To display the service messages, proceed as follows:
The display will normally show the time & date:
##0+.,1 .+#234 2
3868495 8N#M%. #54
Press
/
//
/
followed by
!
!!
!
for the Reset message, the
display will look something like this:
B'@@#I( L1(..+ #)"
##Q.-.) #A$-). ,
Press
/
//
/
followed by
0
00
0
for the Anti-code message,
the display will look something like this:
B'@@#*Q B#)"
Q.-.)#A $-).,
Press
/
//
/
followed by
*
**
*
for the Service message,
the display will look something like this:
B'@@#*@ '+,#B" 9
##?"+#A .+R1>.
!
Press
(
((
(
to exit from the message, the display
will then return to normal.
Fault Messages
K'1(-#0"&.+#DSS
#M%.#54#K'+#7553
There is a Mains failure (the keypad may
chime every minute, enter a valid User
code to stop the chime). The display will
automatically clear when mains is
reapplied.
0C"(.#T1(.#?'%@)
#M%.#54#K'+#7553
There is a Phone Line fault (the keypad
may chime every minute, enter a valid
User code to stop the chime). The
display will automatically clear when line
fault clears.
*+.'#?'1@.<#M.-)
#M%.#54#K'+#7553
Zones that have been placed on test by
the engineer have failed the test (the
system can still be used). Contact your
alarm company to advise.
U')).+$#?'%@)
#M%.#54#K'+#7553
There is a fault with the standby battery
(the keypad may chime every minute,
enter a valid User code to stop the
chime). Contact your alarm company
immediately.
/////// /#M',N .+
#M%.#54 #K'+#7 553
There is a tamper fault (the alarm will
sound, enter a valid User code to silence
the alarm, this fault cannot be cleared).
Contact your alarm company
immediately.
////#?% -.#U@" &(
#M%.#54 #K'+#7 553
A fuse has blown (the alarm will sound,
enter a valid User code to silence the
alarm, this fault cannot be cleared).
Contact your alarm company
immediately.
Other Messages
*@'+,#I (L1(.. +
;"+O1(L #D(#A1 ).
The alarm engineer has logged into the
programming menu and is working on
site (this message will clear when the
engineer logs off or the system is armed.
Q.,").#V.$N'<#1-
("&#TDBVI!#"%)
Too many invalid code attempts have
caused the keypad to lock out. The
keypad will remain like this for 5 minutes.
W#*+.'# A.>%+. <#W
#M%.#54 #K'+#7 553
The keypad has been disabled to prevent
unauthorised access. The display will
automatically clear when the keypad is
enabled.
M1,.#*+,1(L#X
####*9999999
Areas are being armed using one of the
control timers (enter a valid User code to
defer the arming for 30 minutes).
A.+R1>.#Q.Y%1+.<
#M%.#54#K'+#7553
The service timer has expired indicating
that the system requires a service (the
system can still be used). Contact your
alarm company to advise.