Texecom Premier 888 - 4 The User Menu; Accessing the User Menu; View the Event Log

P
rem
i
er
888
&
8168
U
ser
M
anua
l
Th
e
U
ser
M
enu
INS177 19
4. The User Menu
Accessing the User Menu
Advanced operations of the system are carried out using the
User Menu i.e. System Tests, Assigning Users etc.
!
Not all options are available to all users. If an option
cannot be selected, it may be that it is not assigned
to that user (see page 31 for details).
The table below shows the various options available:
User Menu
Key Option Page
)
View System Log
19
)
Change Code
23
)
Edit Chime Zones
23
)
System Tests
24
)
Walk Test
24
)
Enable Engineer
26
)
Set System Time
26
)
Set System Date
27
)
Change Timers
27
)
Change Ctl Times
28
)
Setup Users
30
)
Alter Part Zones
35
)
Call Remote PC
35
➤ To access the User menu, proceed as follows.
The display will normally show the time & date:
##0+.,1 .+#234 2
3868495 8N#M%. #54
!
The top line of the display is programmable.
Enter a valid User code
....
........
....
, the display
should look like this:
!"#$"%#&'()#)"
*+,#-$-).,/
Press
/
//
/
, the display should look like this:
!"#$"%#&'()
G-.+#K.(%/
Press
#
##
#
, the display should look like this:
!"#$" %#&'()# )"
=1.&# A$-).,# T"L/
Press
)
))
)
until the required option is displayed, to select
that option, press
#
##
#
.
Press
(
((
(
to exit the User menu and return to normal.
!
If no keys are pressed, the display will return to
normal after the ‘Menu Time Out’ timer has expired.
View the Event Log
The control panel has two Event Logs, which are time and
date stamped. The first log which is a system log, records
all events that occur on the system, i.e. Users entering their
codes to arm or disarm areas, alarm events, failures to arm
etc. and the second log which is an alarm log, only records
alarm events that occur on the system.
Users with access to this option can view the Event Log to
see what events occurred on the system and when they
occurred.
When viewing the system log there are 8 hotkeys available.
These hotkeys allow certain events to be found easier
without the need for searching (see page 22 for details).
➤ To view the Event Log, proceed as follows:
Enter a valid User code
....
........
....
, the display
should look like this:
!"#$"%#&'()#)"
*+,#-$-).,/
Press
/
//
/
, the display should look like this:
!"#$"%#&'()
G-.+#K.(%/
Press
#
##
#
, the display should look like this:
!"#$" %#&'()# )"
=1.&# A$-).,# T"L/
Press
#
##
#
, the display should look like this:
3#`#A$-).,#T"L
7#`#*@ '+,#T" L
Press
!
!!
!
for the System Log or
0
00
0
for the Alarm Log,
the display will look something like this:
B"<.#53#!'R1<
*+.'6#*UB99999
Press
)
))
)
to scroll up and down through the Log.
!
The down key moves you to the previous event
(backwards in time), and the up key moves you
forwards again.
Use keys
!
!!
!
-
-
--
-
or
&
&&
&
to search for specific
events (see page 22 for details).
Press
%
%%
%
to toggle the display between the area
information and the time/date, the display will look
something like this:
B"<.#53 #!'R1<
#376729 58#54a 5b
Press
/
//
/
when finished, the display should look like
this:
!"#$" %#&'()# )"
=1.&# A$-).,# T"L/