Texecom Premier 888 - To Silent Arm Areas; To Disarm Areas During Entry; To Disarm Areas When Not in Entry; Mode

Th
e
A
rm
i
ng
M
enu
P
rem
i
er
888
&
8168
U
ser
M
anua
l
12 INS177
To Silent Arm Areas
➤ To silent arm areas, proceed as follows:
Ensure that the premises are secure (all doors and
windows closed etc.) and the Ready light is on.
Enter a valid User code
....
........
....
, the display
should look like this:
!"#$"%#&'()#)"
*+,#-$-).,/
Press
)
))
)
until the display looks like this:
!"#$"%#&'()#)"
A1@.()#*+,/
Press
%
%%
%
to arm areas.
Or
Press
'
''
'
to part arm areas.
Continue to arm as normal.
To Cancel the Exit Mode
➤ To cancel the exit mode, proceed as follows:
The display will look something like this:
*+.'-#1 (#IJ1) #X
####*U9 99999#
Enter a valid User code
....
........
....
, the display
should look like this:
!"#$"%# &'()#) "
B'(>.@# IJ1)/
Press
#
##
#
, the exit tone will stop and the display will look
something like this:
###0+.,1.+#222
#M%.#54#K'+#7553
The exit mode has now been cancelled.
To Disarm Areas During Entry
➤ To unset areas, proceed as follows:
Enter the premises via the designated entry point, the
entry tone will start and the display will look something like
this:
*+.'-#1 (#I()+ $#X
####*UB 99999#
Enter a valid User code
....
........
....
, the entry
tone will stop and the display will look something like this:
##0+.,1 .+#234 2
3868495 8N#M%. #54
The selected areas are now disarmed.
!
If the entry timer expires, an Internal alarm will occur
for the duration of the ‘2
nd
Entry Delay’
If the 2
nd
Entry Delay expires, an Intruder alarm will
occur (all internal and external sounders).
To Disarm Areas When Not in Entry
➤ To unset areas, proceed as follows:
The display will look something like this:
*+.'-#* +,.<#X
####*U9 99999
W#A]AMIK#*QKI!#W
#M%.#54#K'+#7553
Enter a valid User code
....
........
....
, the display
should look like this:
!"#$"%#&'()#)"
!1-'+,#A$-).,/
Press
%
%%
%
, the display will look something like this:
A.@.> )#*+.'- #X
##X#W WWWWW99 #\
Use keys
!
!!
!
-
1
11
1
to select/deselect areas that
require disarming i.e.
!
!!
!
and
0
00
0
= Areas A and B,
the display will look something like this:
A.@.> )#*+.'- #X
##X#* UWWWW99 #\
!
Only areas that exist on the system can be selected.
A ‘Star’ means the area can be selected and a ‘Dot’
means the area cannot be selected.
Pressing
2
will select/deselect all areas.
Pressing
%
will toggle between areas A to H and
I to P (Premier 8168 only).
When all the required areas have been selected press
#
##
#
, the display will look something like this:
##0+.,1 .+#234 2
3868495 8N#M%. #54
The selected areas are now disarmed.