Thermal Dynamics CutMaster 58 - 4 T.09 Recommended Cutting Speeds for Mechanized Torch With Shielded Tip

CUTMASTER 58
Manual 0-5544 OPERATION
4T-11
Type Torch: SL60QD With Exposed Tip Type Material: Aluminum
Type Plasma Gas: Air Type Secondary Gas: Single Gas Torch
Thickness Tip Output Amperage
Speed (Per
Minute)
Standoff
Plasma Gas
Press
Flow (CFH) Pierce
Pierce
Height
Inches
mm
(Cat.
No.)
Volts
(VDC)
(Amps) Inches Meters Inches mm psi* bar Plasma Total**
Delay
(Sec)
Inches mm
0.060 1.5 9-8210 110 60 440 11.18 0.25 6.4 75 5.2 90 245 0.00 0.25 6.4
0.075 1.9 9-8210 110 60 440 11.18 0.25 6.4 75 5.2 90 245 0.10 0.25 6.4
0.120 3.0 9-8210 116 60 250 6.35 0.25 6.4 75 5.2 90 245 0.10 0.25 6.4
0.188 3.4 9-8210 116 60 170 4.32 0.25 6.4 75 5.2 90 245 0.20 0.25 6.4
0.250 6.4 9-8210 132 60 85 2.16 0.25 6.4 75 5.2 90 245 0.30 0.25 6.4
0.375 9.5 9-8210 140 60 45 1.14 0.25 6.4 75 5.2 90 245 0.50 0.25 6.4
0.500 12.7 9-8210 143 60 30 0.76 0.25 6.4 75 5.2 90 245 0.80 0.25 6.4
0.625 15.9 9-8210 145 60 20 0.51 0.25 6.4 75 5.2 90 245 NR NR NR
0.750 19.1 9-8210 145 60 18 0.46 0.25 6.4 75 5.2 90 245 NR NR NR
NOTE!
* Gas pressure shown is for torches with leads up to 25’ / 7.6 m long. For 50’ / 15.2 m leads, refer to Section
"Set Operating Pressure" on page 4T-1.
** Total ow rate includes plasma and secondary gas ow
4T.09 Recommended Cutting Speeds for Mechanized Torch With Shielded Tip
Type Torch: SL60QD With Shielded Tip Type Material: Mild Steel
Type Plasma Gas: Air Type Secondary Gas: Single Gas Torch
Thickness Tip Output Amperage
Speed (Per
Minute)
Standoff
Plasma Gas
Press
Flow (CFH) Pierce
Pierce
Height
Inches
mm
(Cat. No.)
Volts
(VDC)
(Amps) Inches Meters Inches mm psi* bar Plasma Total**
Delay
(Sec)
Inches mm
0.036 0.9 9-8208 114 40 170 4.32 0.19 4.8 70 4.8 55 170 0.00 0.2 5.1
0.06 1.5 9-8208 120 40 90 2.29 0.19 4.8 70 4.8 55 170 0.10 0.2 5.1
0.075 1.9 9-8208 121 40 80 2.03 0.19 4.8 70 4.8 55 170 0.30 0.2 5.1
0.135 3.4 9-8208 122 40 75 1.91 0.19 4.8 70 4.8 55 170 0.40 0.2 5.1
0.188 4.8 9-8208 123 40 30 0.76 0.19 4.8 70 4.8 55 170 0.60 0.2 5.1
0.25 6.4 9-8208 125 40 25 0.64 0.19 4.8 70 4.8 55 170 1.00 0.2 5.1
0.375 9.5 9-8208 138 40 11 0.28 0.19 4.8 70 4.8 55 170 NR NR NR
0.500 12.7 9-8208 142 40 7 0.18 0.19 4.8 70 4.8 55 170 NR NR NR
0.625 15.9 9-8208 152 40 3 0.08 0.19 4.8 70 4.8 55 170 NR NR NR