e-STUDIO205L/255/305/355/455 © 2009 TOSHIBA TEC CORPORATION All rights reserved
ERROR CODE AND TROUBLESHOOTING
6 - 10
CB80 Finisher related
service call
Backup RAM data abnormality:
1. Abnormality of checksum value on finisher controller
board is detected when the power is turned on.
[MJ-1025/MJ-1024/MJ-1031]
2. Abnormality of checksum value on punch controller
board is detected when the power is turned on.
[MJ-1025 (when MJ-6005 is installed), MJ-1024
(when MJ-6004 is installed)]
P. 6-86
CB81 Flash ROM abnormality: Abnormality of checksum value
on finisher controller PC board is detected when the
power is turned ON. [MJ-1101]
P. 6-77
CB90 Paper pushing plate motor abnormality: Paper pushing
plate motor is not rotating or paper pushing plate is not
moving normally. [MJ-1024]
P. 6-77
CBA0 Stitch motor (front) abnormality: Stitch motor (front) is not
rotating or rotary cam is not moving normally. [MJ-1024]
P. 6-77
CBB0 Stitch motor (rear) abnormality: Stitch motor (rear) is not
rotating or rotary cam is not moving normally. [MJ-1024]
P. 6-77
CBC0 Alignment motor abnormality: Alignment motor is not
rotating or aligning plate is not moving normally. [MJ-
1024]
P. 6-77
CBD0 Guide motor abnormality: Guide motor is not rotating or
guide is not moving normally. [MJ-1024]
P. 6-77
CBE0 Paper folding motor abnormality: Paper folding motor or
paper folding roller is not rotating normally. [MJ-1024]
P. 6-77
CBF0 Paper positioning plate motor abnormality: Paper
positioning plate motor is not rotating or paper positioning
plate is not moving normally. [MJ-1024]
P. 6-77
CC00 Sensor connector abnormality: Connector of guide home
position sensor, paper pushing plate home position
sensor or paper pushing plate top position sensor is
disconnected. [MJ-1024]
P. 6-77
CC10 Micro switch abnormality: With all covers closed, inlet
door switch, delivery door switch or front cover switch is
open. [MJ-1024]
P. 6-77
CC20 Communication error between finisher and saddle
stitcher: Communication error between finisher controller
PC board and saddle stitcher controller board [MJ-1024]
P. 6-77
CC30 Paddle motor abnormality: The paddle motor is not
rotating normally or the swing guide is not moving
normally. [MJ-1025]
Stack transport motor abnormality: The stack transport
motor is not rotating or the stack transport belt is not
moving normally. [MJ-1101]
Stack delivery motor abnormality: The stack delivery
motor is not rotating normally. [MJ-1031]
P. 6-89
CC31 Transport motor abnormality: The transport motor is not
rotating or the stack transport roller -1 and -2 is not
rotating normally. [MJ-1101]
P. 6-77
CC40 Swing motor abnormality: Swing motor is not rotating or
swing unit is not moving normally. [MJ-1024]
P. 6-77
CC41 Paper holder cam home position abnormality: The paper
holder cam is not at the home position. [MJ-1101]
P. 6-77
CC50 Horizontal registration motor abnormality: The horizontal
registration motor is not rotating normally or the puncher
is not moving normally.
[MJ-1025 (when MJ-6005 is installed)]
Horizontal registration motor abnormality: Horizontal
registration motor is not rotating or puncher is not shifting
normally. [MJ-1024 (when MJ-6004 is installed)]
P. 6-90
CC51 Sideways adjustment motor abnormality P. 6-77
CC52 Skew adjustment motor abnormality P. 6-77
Error code Classification Contents Troubleshooting
To Next Page
Loading...
