Toshiba VF-PS1 - Page 251

K-9
E6581386
11
[6] Speed/torque reference gain/bias setup [3/3] Sensorless vector/vector with sensor (●:Effective, -:Ineffective)
Title
Communi
cation
No.
Function Adjustment range
Minimum
setting unit
(Panel/Communi
cation)
Default
setting
Write during
running
Vector
control
PM
control
V/f Reference
 0230 AI2 input point 2 setting 0~100% 1/1 100 Enabled ●/●●● *2  0231 AI2 input point 2 frequency 0.0~ Hz 0.1/0.01 *1 Enabled ●/●●● *2  0234 RP/high speed pulse input point 1 setting 0~100% 1/1 0 Enabled ●/●●● *3  0235
RP/high speed pulse input point 1 frequency
0.0~ Hz 0.1/0.01 0.0 Enabled ●/●●● *3
 0236 RP/high speed pulse input point 2 setting 0~100% 1/1 100 Enabled ●/●●● *3  0237
RP/high speed pulse input point 2 frequency
0.0~ Hz 0.1/0.01 *1 Enabled ●/●●● *3
*1: Inverter with a model number ending with -WN: 60.0 -WP: 50.0 *2: ⇒ For details, refer to Instruction Manual (E6581341) specified in Section 6.36. *3: ⇒ For details, refer to Instruction Manual (E6581319) specified in Section 6.36.
[7] Operation frequency Sensorless vector/vector with sensor (●:Effective, -:Ineffective)
Title
Communi
cation
No.
Function Adjustment range
Minimum
setting unit
(Panel/Communi
cation)
Default
setting
Write during
running
Vector
control
PM
control
V/f Reference
 0240 Starting frequency setting 0.0~10.0Hz 0.1/0.01 0.1 Enabled ●/●●●6. 7. 1  0241 Operation start frequency 0.0~ Hz 0.1/0.01 0.0 Enabled ●/●●●6. 7. 2  0242 Operation start frequency hysteresis 0.0~30.0Hz 0.1/0.01 0.0 Enabled ●/●●●6. 7. 2  0243 Stop frequency setting 0.0~30.0Hz 0.1/0.01 0.0 Enabled ●/●●●6. 7. 1  0244 Frequency command dead band 0.0~5.0Hz 0.1/0.01 0.0 Enabled ●/●●●6. 7. 3
[8] DC braking Sensorless vector/vector with sensor (●:Effective, -:Ineffective)
Title
Communi
cation
No.
Function Adjustment range
Minimum
setting unit
(Panel/Communi
cation)
Default
setting
Write during
running
Vector
control
PM
control
V/f Reference
 0250 DC braking start frequency 0.0~120.0Hz 0.1/0.01 0.0 Enabled ●/●●●6. 8. 1  0251 DC braking current 0~100% 1/1 50 Enabled ●/●●●6. 8. 1  0252 DC braking time 0.0~20.0 sec. 0.1/0.1 1.0 Enabled ●/●●●6. 8. 1  0253 Forward/reverse DC braking priority control
0:Disabled 1:Enabled
1/1 0 Enabled ●/●●●6. 8. 1
 0254 Motor shaft fixing control
0:Disabled 1:Enabled
1/1 0 Enabled ●/●●●6. 8. 2
 0255 0Hz command output selection
0:Default (DC braking) 1:0Hz command
1/1 0 Enabled -/●●●6. 8. 3
 0256
Time limit for lower-limit frequency operation
0.0:Disabled, 0.1~600.0 sec. 0.1/0.1 0.0 Enabled ●/●●● 6. 9