What does 'FC error left' mean on my tousek ST 63 Gate Opener and how can I fix it?
The 'FC error left' message on your Tousek gate opener indicates that there is no connection between the ST 63 and the frequency converter. Check the correct connection of the FC.
Instructions for installation, connection, adjustments, operation, and servicing by trained professionals.
Emphasizes turning off power supply and outlines manufacturer's liability.
Mandates compliance with rules and post-installation checks.
Warns against use in hazardous areas and non-conforming purposes.
Maintenance tasks are restricted to qualified personnel only.
Recommends monthly checks of the ARS safety reverse system sensitivity.
Statement confirming the ST 63 control unit's compliance with specified EU directives.
Lists key features of the ST 63 control unit for folding and swing gates.
Describes the available operating modes like impulse, automatic, and dead man.
Provides detailed technical specifications for the ST 63 control unit variants.
Crucial warnings regarding electrical shock, explosion hazards, and proper handling.
Critical safety instructions for installation, adjustment, and maintenance of the frequency converter.
Identifies and lists the components within the control box, including converters and terminals.
Lists optional components available for installation within the steel housing.
Important warning about not changing frequency converter settings to avoid voiding the warranty.
Details on optional components like traffic light and dropbolt modules for ST 63.
Explains wiring for standard components and optional modules.
Overview of the ST control board, showing display, buttons, and terminals.
Important note to prevent damage to the electronic circuit board from moisture.
Lists and describes the function of each component on the ST control board.
Important note on connecting optional modules to the specified socket (D).
Critical danger warnings and safety instructions before performing connection works.
Details the terminal assignments for KL1 on the control board for various functions.
Instructions for the STOP button connection and its emergency stop function.
Describes the terminal block KL2 on the DIN rail for power supply and sensor connections.
Key information regarding the connection and routing of motor and sensor wires.
Specifies how to connect sensor wires to terminal block KL2, including length and shielding.
Details the connection of motor wires to the frequency converter (FU-L and FU-R).
Illustrates the wiring diagram for connecting operators to the control unit.
Instructions for using a connection box for EMC conform cable extension.
Explains the use of programming buttons and the text display for adjustments.
Describes the structure of the programming menu, including BASIC SETTINGS and MENU CONTROL.
Details the basic settings required for initial motor operation.
Explains how to access advanced settings through the MENU CONTROL.
Configuration options for buttons and switches like impulse, pedestrian, and stop.
Settings for photocell functions, including inner, outer, and back area photocells.
Configuration options for safety edges on left and right leaves.
Settings related to the left gate leaf, including delays, force, and speed.
Settings related to the right gate leaf, including delays, force, and speed.
Options for selecting operating modes like impulse, automatic, and pedestrian opening.
Configuration options for signal lamps, prewarning lights, and courtyard lighting.
Settings for peripheral devices like traffic lights and locks.
Configuration for electric lock, magnetic clamp, or drop bolt locking.
Settings for additional modules such as status display.
Options for system diagnosis, status display, and factory reset.
Critical danger warnings and safety instructions before performing connection works.
Details on connecting and adjusting various buttons and switches for gate control.
Connection and adjustment options for the impulse button on terminals KL1 30/32.
Connection and adjustment options for the pedestrian button on terminals KL1 30/34.
Describes the ILD channel connection and its function in traffic light or deadman modes.
Details the STOP switch connection and emphasizes its non-emergency stop function.
Explains the CLOSE button connection and its operation in deadman mode.
Describes the OPEN button connection and its operation in deadman mode.
Details the connection of the EMERGENCY MODE switch and its behavior.
Key notes on photocell connection, power supply, and contacts.
Illustrates the connection of inner, outer, and back area photocells.
Instructions for mounting photocells with SYNC function to avoid interference.
Describes the self-monitoring function for photocells and its error response.
Configuration options for the back area photocell.
Settings affecting pause time based on ILD/PHC triggers.
Options to activate or deactivate the photocell self-test function.
Warning regarding deactivation of self-test function and safety category requirements.
Illustrates connection examples for outer and inner photocells with SYNC function.
Wiring diagram for the Tousek LS 26 outer photocell.
Wiring diagram for the Tousek RLS 620 back area reflective photocell.
Important note on adjusting jumpers for transmitter and receiver consistently.
Explains the function and activation of safety sensing edges for obstacle detection.
Crucial notes for programming end positions and safety device triggering.
Configuration options for safety edges LL1 and LL2 on the left gate leaf.
Configuration options for safety edges RL1 and RL2 on the right gate leaf.
Displays the status of safety sensing edges, including triggered or disconnected states.
Settings for opening and closing delay of the left leaf.
Adjustable time delay for the left leaf at opening or closing.
Adjustment of operator force for the left leaf.
Adjustment of motor speed for the left leaf.
Adjustment of soft speed for the left leaf.
Setting for soft stop time in opening and closing directions for the left leaf.
Settings for opening and closing delay of the right leaf.
Adjustable time delay for the right leaf at opening or closing.
Adjustment of operator force for the right leaf.
Adjustment of motor speed for the right leaf.
Adjustment of soft speed for the right leaf.
Setting for soft stop time in opening and closing directions for the right leaf.
Configuration of impulse logic for gate operation, including pause time.
Options for selecting operating modes like impulse, automatic, and pedestrian opening.
Settings for pedestrian opening, defining partial opening based on total opening.
Configuration of automatic closing modes based on pause time.
Settings for pause time logic, including influence and permanent ON modes.
Settings for prewarning signal lamp activation during opening and closing movements.
Configuration for courtyard lighting, including afterglow and timed activation.
Adjustment of green phase duration and clearance time for traffic lights.
Logic settings for traffic light operation, such as continuous red or green on one side.
Activation of the traffic light function and its connection via bus system.
Setup for electric lock, magnetic clamp, or drop bolt locking mechanisms.
Specific settings and operation details for electric lock and magnetic clamp.
Setting the delay time for releasing the magnetic clamp before gate movement.
Configuration for electric lock activation period based on gate situation.
Configuration options for drop bolt locking in open, closed, or both positions.
Configuration of reverse stroke for drop bolt operation to loosen the bolt.
Modes for electric drop bolt operation: OPEN and CLOSE, OPEN only, CLOSE only.
Configuration for gate status display 1 using signal contacts K1 and K2.
Configuration for gate status display 2, including movement and stop status.
Step-by-step guide for connecting the electric lock/magnetic clamp module.
Information and steps for installing the optional dropbolt module.
Details on connecting the dropbolt module (E) to the control unit (ST).
Instructions for wiring dropbolts directly to the terminal blocks (K) of the motor print boards.
Overview of the SAFELOCK dropbolt control unit, installed on the steel cabinet door.
Explains the meaning of status display codes for various inputs and states.
Option to delete the determined gate end positions ('gate closed' and 'gate open').
Procedure to reset all settings back to factory defaults.
Displays the software version and serial number of the control unit.
Details on how to view the protocol list of all recorded events.
Guide for plugging in the receiver board and key notes on its use and programming.
Crucial preparation steps before putting the system into operation, including safety.
Guide for selecting language and gate type (swing/folding) during initial operation.
Steps for adjusting the most important motor settings in the 'Basic Settings' menu.
Adjusting the settings for the outer photocell.
Adjusting the settings for the back area photocell.
Adjusting the settings for safety edge LL1 on the left leaf.
Adjusting the settings for safety edge LL2 on the left leaf.
Adjusting the settings for safety edge RL1 on the right leaf.
Adjusting the settings for safety edge RL2 on the right leaf.
Selecting and configuring the operating mode from factory settings.
Guide for the automatic positioning process of gate end points.
General information about the STA 11 traffic light control unit and its capabilities.
Provides technical specifications for the STA 11 traffic light control unit.
Describes the operational functions of the STA 11 traffic light system.
Outlines the sequence of traffic light operations, including prewarning and green phases.
Lists and describes the components of the traffic light control board STA 11.
Critical safety warnings for opening the control housing and handling powered units.
Warning to ensure electronics are not damaged by moisture during maintenance.
Note that limit switch connection is not necessary for ST 63; terminals 60/61 must be bridged.
How to connect induction loops for green request using the STA 11.
How to connect impulse switches for green request on the STA 11.
Information regarding the limit switch input (terminals 60/61) for STA 11.
Details on connecting traffic lights to the output terminals of the STA 11.
Wiring the traffic light board to the operator control board via the bus system.
How operator control board settings affect traffic light functions.
Key instructions for installing and using radio receivers with traffic light mode.
Crucial information about the ISD 6 loop detector device, its function, and installation.
Steps for mounting and installing the ISD 6 induction loop detector.
Lists common errors displayed by the unit and their potential causes.
Provides recommended solutions and checks for resolving common operational errors.
General| Brand | tousek |
|---|---|
| Model | ST 63 |
| Category | Gate Opener |
| Language | English |
To Next Page
