TRENDnet TI-PG1284i User Manual

© Copyright 2016 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TI-PG1284i
154
configure
port-security
(disable|enable)
This command enables / disables the global
port security function.
interface
port-security
(disable|enable)
This command enables / disables the port
security function on the specific port.
interface
port-security limit
VALUE
This command configures the maximum MAC
entries on the specific port.
configure
interface range
gigabitethernet1/0/
PORTLISTS
This command enters the interface configure
node.
if-range
port-security
(disable|enable)
This command enables / disables the port
security function for the specified ports
if-range
port-security limit
VALUE
This command configures the maximum MAC
entries for the specified ports.
Web Configuration
Security > IP Source Guard > Port Security
Parameter
Description
Port Security Settings
Port Security
Select Enable/Disable to permit Port Security on the Switch.
Port
Select a port number to configure.
State
Select Enable/Disable to permit Port Security on the port.
Maximum MAC
The maximum number of MAC addresses allowed per interface.
The acceptable range is 1 to 30.
Port Security Status
Port
This field displays a port number.
State
This field displays if Port Security is Enabled or Disabled
Maximum MAC
This field displays the maximum number of MAC addresses
TACACS+
The purpose of this enhancement is to support TACACS+ on the Switch platforms.
Terminal Access Controller Access Control System Plus is a security application that
provides centralized validation of users attempting to gain access to a router, network
access server etc. In order for the TACACS+ feature work it would need a TACACS+ server,
which would typically be a daemon running on a centralized UNIX or windows NT
authentication, authorization and accounting facilities for managing network access
points from a single management service.
Product Features
The TACACS+ implementation will support the following features:
 The implementation will conform to version 1.78 of the TACACS+ draft RFC.
 Authentication, Authorization and Accounting can be run as well as disabled
independently of each other.
 In case TACACS+ authentication fails on account of the server being
unreachable the box can be made to default to a local authentication policy.
 TACACS+ packet body encryption will be supported.
 Single Tacacs+ server will be support.

TRENDnet TI-PG1284i Specifications

General

Switch type	Managed
Switch layer	L2+
System event log	Yes
10G support	No
Number of VLANs	256
Networking standards	IEEE 802.1D, IEEE 802.1Q, IEEE 802.1ab, IEEE 802.1p, IEEE 802.1s, IEEE 802.1w, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3at, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Virtual LAN features	Tagged VLAN, Protocol-based VLAN
Console port	RJ-45
SFP module slots quantity	4
Installed SFP modules quantity	0
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity	8
Stackable	-
Certification	CE, FCC
Product color	Black
International Protection (IP) code	IP30
Throughput	17.86 Mpps
Jumbo frames	10000
MAC address table	16000 entries
Packet buffer memory	128 MB
DHCP features	DHCP server
Authentication	Port-based authentication
Security algorithms	802.1x RADIUS, HTTPS, SNMP
Multicast MAC address table	256 entries
Output current	5 A
Output voltage	48 V
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (max)	260 W
Total Power over Ethernet (PoE) budget	240 W
Power over Ethernet (PoE) power per port	30 W
Operating temperature (T-T)	-40 - 70 °C
Operating relative humidity (H-H)	0 - 95 %
Mean time between failures (MTBF)	322805 h
Harmonized System (HS) code	85176990

Weight and Dimensions

Depth	132 mm
Width	170 mm
Height	50 mm
Weight	920 g