EasyManuals Logo

TRENDnet TI-PG1284i User Manual

TRENDnet TI-PG1284i
192 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #175 background imageLoading...
Page #175 background image
© Copyright 2016 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TI-PG1284i
172
configure
mail-alarm mail-from
This command configures the mail
sender.
configure
mail-alarm mail-to
This command configures the mail
receiver.
configure
mail-alarm server-ip
IPADDR server-port VALUE
This command configures the mail
server IP address and the TCP port.
configure
mail-alarm server-ip
IPADDR server-port Default
This command configures the mail
server IP address and configures 25 as
the server’s TCP port.
configure
mail-alarm trap-event
(reboot|link-
change|config.|
firmware|login|port-
blocked| alarm)
(disable|enable)
This command disables / enables mail
trap events.
Web Configuration
Management > Mail Alarm
Parameter
Description
State
Enable / disable the Mail Alarm function.
Server IP
Specifies the mail server’s IP address.
Server Port
Specifies the TCP port for the SMTP.
Account Name
Specifies the mail account name.
Account Password
Specifies the mail account password.
Mail From
Specifies the mail sender.
Mail To
Specifies the mail receiver.
Trap State
Enables / disables the mail trap event states.
Maintenance
CLI Configuration
Node
Command
Description
enable
show config-
change-status
This command displays the configurations status if
there are default values.
configure
reboot
This command reboots the system.
configure
reload default-
config
This command copies a default-config file to
replace the current one.
Note: The system will reboot automatically to take
effect the configurations.
configure
write memory
This command writes current operating
configurations to the configuration file.
configure
archive download-
config <URL PATH>
This command downloads a new copy of
configuration file from TFTP server.
Where <URL PATH> can be:
ftp://user:pass@192.168.1.1/file
http://192.168.1.1/file

Table of Contents

Other manuals for TRENDnet TI-PG1284i

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the TRENDnet TI-PG1284i and is the answer not in the manual?

TRENDnet TI-PG1284i Specifications

General IconGeneral
Switch typeManaged
Switch layerL2+
System event logYes
10G supportNo
Number of VLANs256
Networking standardsIEEE 802.1D, IEEE 802.1Q, IEEE 802.1ab, IEEE 802.1p, IEEE 802.1s, IEEE 802.1w, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3at, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Virtual LAN featuresTagged VLAN, Protocol-based VLAN
Console portRJ-45
SFP module slots quantity4
Installed SFP modules quantity0
Basic switching RJ-45 Ethernet ports typeGigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity8
Stackable-
CertificationCE, FCC
Product colorBlack
International Protection (IP) codeIP30
Throughput17.86 Mpps
Jumbo frames10000
MAC address table16000 entries
Packet buffer memory128 MB
DHCP featuresDHCP server
AuthenticationPort-based authentication
Security algorithms802.1x RADIUS, HTTPS, SNMP
Multicast MAC address table256 entries
Output current5 A
Output voltage48 V
AC input voltage100 - 240 V
AC input frequency50 - 60 Hz
Power consumption (max)260 W
Total Power over Ethernet (PoE) budget240 W
Power over Ethernet (PoE) power per port30 W
Operating temperature (T-T)-40 - 70 °C
Operating relative humidity (H-H)0 - 95 %
Mean time between failures (MTBF)322805 h
Harmonized System (HS) code85176990
Weight and Dimensions IconWeight and Dimensions
Depth132 mm
Width170 mm
Height50 mm
Weight920 g

Related product manuals