What to do if the Ulvac LR Water Pump power cannot be applied?
First, ensure that the power is correctly supplied to the pump. If the power supply is not the issue, check the wiring connections of the connector, and correct them if they are incorrect. Finally, inspect the pump for any leaks. If a leak is found, disassemble and repair the pump.
Why is my Ulvac LR making an unusual sound?
An unusual sound from the Ulvac Water Pump can be caused by several factors. The panel might be vibrating. The sound may be high due to resonance in the piping when gas is being fed; try using a pipe with a thicker wall to suppress the sound. Check the exhaust piping, or there may be a leakage at the inlet port, so check the piping and repair it, if needed, or there may be a rise in backing pressure.
What to do if Ulvac LR controller can not activates the Pump?
If the controller cannot activate the Ulvac Water Pump, make sure that LOCAL mode is selected by pressing the REMOTE/LOCAL switch on the controller. Also, ensure that the STOP SWITCH is turned off. Check if EMERGENCY STOP is displayed, and if so, ensure the emergency stop pin of the remote operation connector is shorted. Finally, verify that INTERLOCK is not displayed; if it is, the external interlock pin of the remote operation connector is not shorted.
What to do if my Ulvac LR shows no indication on display?
If there is no indication on the display of your Ulvac Water Pump, verify that the breaker is turned on. If it is on and there's still no display, consider replacing the instrumentation.
What to do if I see WATER FLOW LOW ALARM on my Ulvac Water Pump?
If you see a 'WATER FLOW LOW ALARM' on your Ulvac Water Pump, try opening the flow rate-regulating valve. Also, check if there is insufficient difference pressure at the inlet/outlet ports and increase the supply pressure from the host equipment. Make sure there is sufficient gas supply from host equipment.
What to do if I see DRP/MBP PUMP TEMP HIGH ALARM on my Ulvac LR Water Pump?
If you see a 'DRP/MBP PUMP TEMP HIGH ALARM' on your Ulvac Water Pump, lower the environment temperature. Also, check for insufficient cooling water and open the flow rate-regulating valve. If you have a booster pump unit of HR series, ensure the inlet pressure is operating within the range from the ultimate pressure to 200Pa. Clean and wash the exhaust pipe if there is an increase in backing pressure.
What to do if the pressure does not lower in Ulvac Water Pump?
If the pressure does not lower in your Ulvac Water Pump, check the piping at the upstream of the PUMP for any clogs in the intake port wire netting. Ensure that the pump operating temperature is static, and if not, measure again one hour later. The ultimate pressure in the Specifications is the value directly above the pump.
What to do if I see N PURGE 2 GAS LOW ALARM on my Ulvac LR?
If you see an 'N PURGE 2 GAS LOW ALARM' on your Ulvac Water Pump, open the flow rate-regulating valve. Increase the supply pressure from the host equipment if there is insufficient difference pressure at the inlet/outlet ports. Ensure there is a sufficient supply of gas.
What does it mean when my Ulvac LR displays SYSTEM ERROR?
If your Ulvac Water Pump displays a 'SYSTEM ERROR', turn off the power and turn it on again. This may resolve the issue if the PC program is out of control or the control power output is low.
What to do if the temperature does not increase in Ulvac LR (only HR series)?
If the temperature does not increase in your Ulvac Water Pump (HR series only), operate it for one hour. If the temperature still doesn't increase after a temperature error, turn on the bimetal switch, as it may have been turned off. In case of exhaust pipe issues, operate for one hour, and if the temperature remains low, exchange the mantle heater because the temperature fuse has been cut when the temperature does not increase after of the temperature error.
Defines technical terms and hazard levels for warnings.
Explains labels attached to warning locations for safety.
Explains the purpose and application of the LR/HR series pumps.
Describes the pump's capabilities and physical makeup.
Details nitrogen gas and cooling water systems for the pump.
Lists the required utilities and their specifications for pump operation.
Provides detailed dimensions for various pump models.
Explains the functions of the controller buttons and indicators.
Identifies and describes the pump's utility connection ports.
Graphs illustrating pump performance characteristics like speed and current.
General safety precautions for pump installation and operation.
Guidelines for unpacking, transit, storage, and environmental conditions.
Covers requirements for all pump piping connections.
Details on electrical wiring for power and remote control.
Procedures for PC communication setup and connections.
Visual representation of the pump's operational sequence.
Steps to perform before starting pump operation.
How to choose between local and remote control modes.
Procedures for starting and stopping the pump.
How to monitor the pump's current operating status.
Instructions for modifying operational set items.
Details the different operational modes available for the pump.
A list of configurable parameters and their settings.
Explains how the pump monitors itself for abnormalities.
Describes how the pump records operational events and alarms.
Routine checks to perform on the pump and controller.
Recommended schedules for pump overhauling and part replacement.
Identifies common pump symptoms and their corrective actions.
Lists alarm signals and their causes/solutions.
Identifies the specific product covered by the warranty.
Specifies the duration of the product warranty.
Details what is and is not covered by the warranty.
Instructions on contacting ULVAC for service or support.
Additional information regarding contracts and product usage.
Guidance on replacing fuses in CE type pumps.
Diagrams showing RS-232C and RS-485 connector pin assignments.
Lists commands for controlling and monitoring the pump via PC.
General| Brand | Ulvac |
|---|---|
| Model | LR Series |
| Category | Water Pump |
| Language | English |
To Next Page
