VTech DS6311-2 User Manual

73
Appendix
Replace a handset
If you want to replace a handset or re-assign the designated handset number
of a registered handset, you must deregister all the handsets and then
individually register each handset.
To make deregistration easier, read all of the instructions on this page before
you begin.
To deregister all handsets:
Press and hold FIND HANDSET on the telephone base for about 10
seconds until the IN USENKIJVƀCUJGUVJGPTGNGCUGFIND HANDSET.
Press FIND HANDSET again at once. You must press FIND HANDSET
while the IN USENKIJVKUUVKNNƀCUJKPI6JGIN USENKIJVƀCUJGUHQTCDQWV
seven seconds.
All system handsets show
Press and hold FIND HANDSET on base for
4 sec, then press # on handset
when the deregistration completes. The
deregistration process takes about 10 seconds to complete.
If deregistration fails, you may need to reset the telephone and try again.
To reset:
Pick up the regisered handset and then press
/TALK/FLASH.
Press OFF/CLEAR and place the handset back in the telephone base.
-OR-
Unplug the power from the telephone base, then plug it back in.
1.
2.
3.
1.
2.
•
You cannot deregister a handset if any system handset is in use.
74
Appendix
+H[QWJCXGFKHſEWNV[YKVJ[QWTVGNGRJQPGRNGCUGVT[VJGUWIIGUVKQPUDGNQY
For Customer Service, visit our website at www.vtechphones.com or call
1 (800) 595-9511.
I cannot pair my cell phone to the telephone base.
Make sure the Bluetooth function of your cell phone is turned on. See the user’s
manual of your cell phone for more information.
Remove VTech DS6321 from your cell phone’s handsfree device history list (see
the user’s manual of your cell phone for more information).
Carefully follow the pairing instructions on page 14 and make sure that your cell
phone is not connected to any other Bluetooth device.
Turn off your cell phone, then turn it on again.
Reset the telephone base. Unplug the unit’s electrical power. Wait for
approximately 15 seconds, then plug it back in. Repeat the above suggestions.
I cannot pair my headset to the telephone base
Make sure that your Bluetooth headset is in discoverable mode when pairing with
the telephone base. See the user’s manual of your headset for more information
on how to set your headset in discoverable mode.
Carefully follow the pairing instructions on page 16 and make sure that your
headset is not connected to any other Bluetooth device.
Reset the telephone base. Unplug the unit’s electrical power. Wait for
approximately 15 seconds, then plug it back in. Repeat the above suggestions.
I cannot connect my cell phone with the telephone base.
Make sure that the Bluetooth function of your cell phone is turned on. See the
user’s manual of your cell phone for more information.
Make sure that your Bluetooth cell phone is not connected to any other Bluetooth
device.
Turn off your cell phone, then turn it on again.
Make sure that your cell phone is connected and on the Active Devices list.
For some cell phones, you must authorize VTech DS6321 device in your cell
phone’s Bluetooth feature. See the user’s manual of your cell phone for more
information.
Manually connect your cell phone to VTech DS6321. Refer to the user’s manual of
your cell phone for more information.
I cannot connect my headset with the telephone base.
Make sure that your Bluetooth headset is not connected to any other Bluetooth
device.
Make sure that your headset is connected and on the Active Devices list.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Troubleshooting

VTech DS6311-2 Specifications

General

Brand	VTech
Model	DS6311-2
Category	Cordless Telephone
Language	English