Electrical:
The WAZER Pro comes as two different models
for the specific frequency regions. This setup
guide is for both the 60hz region and 50hz
versions. Power requirements are: Split-Phase
230 VAC 60hz for WAZER Pro (60Hz) and Single
Phase 230 VAC 50hz for WAZER Pro (50Hz).
WAZER Pro 50Hz uses IEC 60309-2P electric
plug; WAZER Pro 60Hz uses NEMA 6-20 plug.
Please follow the appropriate electrical
instructions below given your model of WAZER
Pro. You can verify your model by looking at
the Primary Label on the right side window.
Corresponding receptacles are shipped with
the machine. If you cannot locate appropriate
receptacle, please have a professional
electrician to connect the receptacle.
The included receptacle
can only be installed by licensed
electrician. Failure to do so may result in
electrocution, serious injury or death.
High load motors usually requires an “in-rush
current” that will momentarily exceed the
stated steady-state run currents for a fraction
of a second. The time associated with this
“in-rush current” is very short and almost all
household and commercial AC breakers are
designed to handle this safely. However, in the
rare case that you run into trouble with your
breaker tripping, consult an electrician to have
your system checked to handle on the order of
60amps for 150 milliseconds.
Water Supply:
• Flow Rate: Greater than 2 gpm (7.6L/min).
Most household and commercial water
plumbing meet this requirement.
• Pressure: 30-90 psi (0.20MPa – 0.60MPa).
Most household and commercial water
plumbing systems fall in this range. The
higher in that range, the better for the Pump
in terms of its longevity.
• Temperature: MAX 130°F (54°C). DO NOT
use a hot water line for WAZER Pro.
• Water Hardness: Less than 180 mg/L (10.5
gpg). Water hardness is the biggest factor
that affects the longevity of the components.
We suggest you search your local water
condition if this is a concern.
Water Drainage:
Make sure your drain location is no more
than 30 feet (9m) from your WAZER Pro.
Additionally, the drain location should be less
than 4 feet (1.2m) above WAZER Pro.
Floor space:
• Sturdy and capable of holding over 1300 lbs.
(600kg)
• Flat and level under load. Maximum 1.5mm
of height difference across entire Cut Bed
• A clear area of 46” by 27” (1.2m by 0.7m) to
allow for access.
• Does not deteriorate when exposed to water.
Because under some unforeseen scenarios,
water may stream out from abrasive hopper
and other places.
• Please keep a 80” (2m) area above the floor
footprint, to allow door window to open.
• WAZER Pro Should be placed in environment
such as laboratories, household workshops
and most machines shops. Heavy Industrial
facility with machinery or devices that induce
electromagnetic interference on adjacent
devices should be avoided.
Ambient Air Temperature: 40 - 100 F / 5 - 40 C
WAZER Pro should never be operated outside
of this range.
Space Around WAZER Pro: Make sure to leave
at least 12” (0.4m) of free space on the right
and left sides of WAZER Pro. On the left side
of WAZER Pro, you will need room to refill the
Abrasive Hopper. On the right side, you may
need access to the Control Panel.
Wet Area: WAZER Pro operates with abrasive
and water. Though WAZER Pro is enclosed, it
is not a sealed system, and water and abrasive
will inevitably leak on occasion. The floor
surface should be water- resistant, slip proof
and smooth.
Noise: WAZER Pro emits noise that would be
disruptive in settings such as classrooms and
offices. Make sure to place WAZER Pro in a
location where the noise level of traditional
shop tools like drills and saws is acceptable.
Choosing a Location for WAZER Pro
Location Requirements
Ensure that your installation location meets ALL the following requirements:
Note 1, Pg. 5
Setting Up WAZER Pro |
SECTION 4
27
To Next Page
Loading...