YASKAWA 1000 Series

Other manuals for YASKAWA 1000 Series

Questions and Answers:

H
Heidi KimSep 1, 2025
What to do if YASKAWA 1000 DC Drives show Serial Communication Transmission Error?
- D
  Denise SimonSep 1, 2025
  If you're experiencing a Serial Communication Transmission Error with your YASKAWA DC Drive, begin by inspecting the communication wiring and terminal resistor connections for faults, short circuits, or improperly connected components. Correct any wiring errors, remove ground shorts, and reconnect any loose wires. Also, review the master-side programming for errors, particularly at start-up. If the issue persists, perform a self-diagnostics check, and if the fault continues, replace the drive, as the communication circuitry may be damaged.
D
Donald CookSep 1, 2025
What to do if YASKAWA 1000 have External Fault Input from the option?
- J
  Justin McculloughSep 1, 2025
  If the YASKAWA DC Drive indicates an External Fault Input from the option, it means an external fault is being sent from the main controller (PLC). To resolve this, first, remove the cause of the external fault. Then, reset the external fault input from the PLC device. If the problem persists, check the PLC program for any issues and make the necessary corrections.
K
kathrynmilesSep 2, 2025
Why YASKAWA 1000 DC Drives show Vendor specific error?
- J
  Jeffrey WilliamsSep 2, 2025
  If your YASKAWA DC Drive displays 'Vendor specific error', this could be due to attempting to change a drive constant while the drive is running, or attempting to change a drive constant to a value outside of the setting range. To fix this, stop the drive and specify a value that is within the setting range.
M
Michael GarzaSep 2, 2025
What causes Object state conflict in YASKAWA 1000 DC Drives?
- A
  Alicia SolisSep 2, 2025
  If the YASKAWA DC Drive displays the error 'Object state conflict', it means you've attempted to change a drive constant that cannot be changed while the drive is running. To resolve this, stop the drive before attempting to change the constant.
J
Jamie JenningsSep 3, 2025
How to resolve Invalid parameter error in YASKAWA 1000?
- M
  Michele SolisSep 3, 2025
  If your YASKAWA DC Drive shows 'Invalid parameter', it means you've attempted to change to a data value outside of the setting range. To correct this, specify a data value that is within the setting range.
J
Jonathan CarsonSep 3, 2025
Why YASKAWA 1000 DC Drives show Option Fault (CN5-B) when using AI-A3 or D1-A3?
- C
  chendanielSep 3, 2025
  If your YASKAWA DC Drive displays 'Option Fault (CN5-B)', and you have options AI-A3 or D1-A3 connected to the CN5-B port while an option was connected to CN5-A, know that only one of these options, AI-A3, DI-A3 or SI-?? option can be connected to the drive at the same time. The SI-N3 must be connected to CN5-A.
A
amanda77Sep 4, 2025
Why YASKAWA DC Drives show Option Fault (CN5-C) when using AI-A3 or D1-A3?
- E
  Erin KelleySep 4, 2025
  If your YASKAWA DC Drive displays 'Option Fault (CN5-C)', and you have options AI-A3 or D1-A3 connected to the CN5-C port while an option was connected to CN5-A, know that only one of these options, AI-A3, DI-A3 or SI-?? option can be connected to the drive at the same time. The SI-N3 must be connected to CN5-A.
R
romerokaitlynSep 4, 2025
How to fix Service not supported error in YASKAWA 1000?
- M
  Mary Diaz DVMSep 5, 2025
  If your YASKAWA DC Drive displays 'Service not supported', it indicates that the service code is incorrect. Correct the service code to resolve this issue.
L
Lori HurleySep 5, 2025
How to resolve Invalid attribute value error in YASKAWA 1000?
- D
  Danielle HarrisSep 5, 2025
  If your YASKAWA DC Drive displays 'Invalid attribute value', it means that the attribute is incorrect. Correct the attribute to resolve this issue.
A
Amanda ElliottSep 6, 2025
What causes Attribute not settable error in YASKAWA DC Drives?
- R
  Rachel ReedSep 6, 2025
  If your YASKAWA DC Drive shows 'Attribute not settable', it means you've attempted to change a read-only attribute. To resolve this, correct the service code or attribute setting.

YASKAWA 1000 Series Specifications

General

Series	1000 Series
Category	DC Drives
Cooling Method	Forced air cooling
Protection Features	Overcurrent, Overvoltage, Undervoltage, Overtemperature, Short Circuit
Communication Interface	Modbus RTU
Storage Temperature	-20°C to +60°C
Humidity	5% to 95% (non-condensing)
Enclosure Rating	IP20
Input Voltage	200-240V AC, 380-480V AC

Summary

Preface and Safety

Applicable Documentation

Describes related manuals for installation and operation of the DeviceNet option.

Terms and Abbreviations

Defines key terms and acronyms used throughout the manual.

Safety Information and Precautions

Details general safety guidelines, warning conventions, and essential precautions.

Product Overview

About the DeviceNet SI-N3 Option

Explains the purpose, functionality, and benefits of the DeviceNet SI-N3 option module.

Applicable Drive Models

Lists the Yaskawa AC Drive 1000-Series models compatible with this option.

Receiving and Package Contents

Receiving Inspection Procedures

Outlines essential steps to perform upon receiving the DeviceNet option.

Installation Tools Required

Lists the necessary tools for the proper installation of the option module.

DeviceNet Option Components

Physical Description and Terminal Block

Describes the physical layout of the DeviceNet option and details the terminal block connections.

LED Status Indicators and Diagnostics

Explains the meaning of LED displays and the power-up diagnostic sequence.

Installation Procedure

Safety Precautions and Preparation

Covers crucial safety rules, precautions, and pre-installation checks.

Physical Installation Steps

Details the step-by-step process of mounting the option and connecting wires.

Network Configuration Settings

Explains how to set MAC ID, Baud Rate, and obtain EDS files for network setup.

Related Drive Parameters

Configuring DeviceNet Messaging

Drive Configuration on DeviceNet

Describes how the drive is configured for DeviceNet communication.

Polled Communication Setup

Details configuring Polled Consuming/Producing Assemblies (PCA/PPA).

Additional Connection Path Support

Covers alternative methods for setting connection paths for data exchange.

Output Assemblies (Drive Consumes)

Detailed Output Assembly Descriptions

Lists and describes data structures sent from the network to the drive for control.

Input Assemblies (Drive Produces)

Detailed Input Assembly Descriptions

Lists and describes data structures sent from the drive to the network for status.

DeviceNet Standard Class Objects

Overview of General Class Objects

Introduces standard DeviceNet objects like Identity, Message Router, and Connection Objects.

Vendor-Specific Yaskawa Class Objects

Yaskawa Drive Parameters Object

Provides access to Yaskawa drive parameters via MEMOBUS/Modbus addresses.

Yaskawa MonitorControl Object

Offers drive monitoring and control functions through DeviceNet.

Troubleshooting DeviceNet Issues

Drive-Side Error Codes and Faults

Explains common drive errors, fault displays, and their causes.

Specific Communication Errors

Covers minor faults, alarms, explicit message errors, and communication issues.

DeviceNet Error Codes and Monitors

Details DeviceNet-specific error codes and status monitoring parameters.

Automatic Address Recovery Features

Describes ADR and AAR for automatic device replacement and configuration.

DeviceNet Network Cabling Specifications

Trunk Line Length Limits

Specifies maximum allowable lengths for the main DeviceNet trunk line.

Drop Line Length Limits

Specifies maximum allowable lengths for DeviceNet drop lines.

DeviceNet Option Specifications

Revision History

Tracks manual updates, publication dates, and revision numbers.

Related product manuals

YASKAWA V1000 SI-S3/V

35 pages

YASKAWA CIMR-VCBA0003

152 pages

YASKAWA GA700 GA700 Series

32 pages

YASKAWA GA500 GA50U Series

524 pages

YASKAWA GA800 GA80U Series

98 pages

YASKAWA L1000A CIMR-LC F Series

106 pages

Table of Contents