EasyManuals Logo

Yealink SIP-T42S User Manual

Yealink SIP-T42S
200 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #147 background imageLoading...
Page #147 background image
Advanced Phone Features
137
2. Press the BLF key of the monitored user again or the Transfer soft key to complete the
transfer when receiving ringback.
To perform an attended transfer:
1. Press the BLF key of the monitored user which you want to transfer this call to. The phone
will dial the number of the monitored user.
2. Press the BLF key of the monitored user again or the Transfer soft key to complete the
transfer after the monitored user answers the call.
When the transfer mode on DSS key is set to New Call and there is already an active call on the
IP phone, you can do the following:
To perform a new call:
1. Press the BLF key of the monitored user you want to call.
The phone will dial the number of the monitored user. The original call is placed on hold.
Picking up an Incoming Call of the Monitored User
When the monitored user receives an incoming call, the BLF key indicator of the monitored user
will flash red. You can use the BLF key to pick up an incoming call of the monitored user. If you
enable visual alert feature on the phone, you can pick up the incoming call using the DPickup
soft key. Before picking up an incoming call, ensure that the directed call pickup code has been
configured in advance.
To pick up an incoming call using the BLF key or the DPickup soft key:
1. Press the BLF key or the DPickup soft key.
The incoming call of the monitored user is answered on the IP phone.
Note
Parking a Call/Retrieving a Parked Call to the Monitored User
You can press the desired BLF key to park a call or retrieve a parked call directly in FAC mode. It
should be pre-configured by your system administrator.
To park a call in FAC mode:
1. During a call, press the Park soft key (You may need to press the More soft key to see the
Park soft key).
2. Press the desired BLF key to park the call to the monitored user.
If the call pickup code is not configured, the phone will place a call to the monitored user
instead of picking up an incoming call of the monitored user when you press the BLF key or the
DPickup soft key.

Table of Contents

Other manuals for Yealink SIP-T42S

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Yealink SIP-T42S and is the answer not in the manual?

Yealink SIP-T42S Specifications

General IconGeneral
ManualYes
Cables includedLAN (RJ-45)
Number of handles included1 pc(s)
Lines quantity12 lines
Phonebook capacity1000 entries
Number of VoIP accounts12
MountingDesk/Wall
Handset typeWired handset
Product typeIP Phone
Product colorBlack
Voice codecsCNG, G.711Mu, G.711a, G.723.1, G.726, G.729ab, VAD, iLBC
Operating temperature (T-T)-10 - 50 °C
Operating relative humidity (H-H)10 - 95 %
Display diagonal2.7 \
Display resolution192 x 64 pixels
AC adapter input voltage100 - 240 V
AC adapter output current1.2 A
AC adapter output voltage5 V
Dual-Tone Multi-Frequency (DTMF) modesIn-band, Out-of band, SIP info
Volume controlDigital
Number of programmable keys6
USB 2.0 ports quantity1
Ethernet LAN (RJ-45) ports2
Networking standardsIEEE 802.3af
Ethernet LAN data rates10, 100 Mbit/s
Ethernet LAN interface typeFast Ethernet
Supported network protocolsSIP v1, SIP v2, LLDP/CDP/DHCP, OpenVPN, IEEE802.1X, IPv6, FTP/TFTP/HTTP/HTTPS
Weight and Dimensions IconWeight and Dimensions
Depth189 mm
Width212 mm
Height175 mm
Package depth223 mm
Package width246 mm
Package height120 mm

Related product manuals