Yealink SIP-T46S Administrator's Guide

Administrator’s Guide for SIP-T2 Series/T4 Series/T5 Series/CP920 IP Phones
367
Values
T53W/T53/T43U/T42U/T42S/T42G: Integer from 1 to 12;
T41P/T41S/T27G: Integer from 1 to 6;
T40P/T40G/T23P/T23G: Integer from 1 to 3;
T21(P) E2: Integer from 1 to 2;
T19(P) E2/CP920: 1.
Default
1
Parameter
dialplan.emergency.custom_asserted_id <y0000000000xx>.cfg
Description
It configures the custom outbound identity when placing an emergency call.
Note: It works only if “dialplan.emergency.enable” is set to 1 (Enabled) and “dial-
plan.emergency.asserted_id_source” is not set to HELD.
Permitted
Values
A number with 10 to 25 digits - for example, 1234567890. The SIP URI constructed from the number
and SIP server (for example, abc.com) is included in the P-Asserted-Identity (PAI) header (for
example, <sip:1234567890@abc.com > ).
SIP URI - for example, sip:1234567890123@abc.com. The full URI is included in the P-Asserted-Iden-
tity (PAI) header and the address will be replaced by the emergency server (for example,
<sip:1234567890123@emergency.com > ).
TEL URI - for example, tel:+16045558000. The full URI is included in the P-Asserted-Identity (PAI)
header (for example, <tel:+16045558000 > ).
Default
Blank
Parameter
dialplan.emergency.server.X.address
[1]
<y0000000000xx>.cfg
Description
It configures the IP address or domain name of the emergency server X to be used for routing calls.
Note: If the account information has been configured (no matter whether the account registration suc-
ceeds or fails), the emergency calls will be dialed using the following priority: SIP server > emergency
server; if not, the emergency server will be used. It works only if “dialplan.emergency.enable” is set to
1 (Enabled) and “dialplan.emergency.asserted_id_source” is not set to HELD.
Permitted
Values
IP address or domain name
Default
Blank
Parameter
dialplan.emergency.server.X.port
[1]
<y0000000000xx>.cfg
Description
It configures the port of emergency server X to be used for routing calls.
Note: It works only if “dialplan.emergency.enable” is set to 1 (Enabled) and “dial-
plan.emergency.asserted_id_source” is not set to HELD.
Permitted
Values
Integer from 0 to 65535
Default
5060
Parameter
dialplan.emergency.server.X.transport_type
[1]
<y0000000000xx>.cfg
Description
It configures the transport protocol the phones use to communicate with the emergency server X.
Note: It works only if “dialplan.emergency.enable” is set to 1 (Enabled) and “dial-
plan.emergency.asserted_id_source” is not set to HELD.
Permitted
Values
0-UDP
1-TCP
2-TLS

Yealink SIP-T46S Specifications

General

Manual	Yes
Cables included	LAN (RJ-45)
Number of handles included	1 pc(s)
Mounting	Desk/Wall
Handset type	Wired handset
Product type	IP Phone
Product color	Black
Voice codecs	CNG, G.711Mu, G.711a, G.722, G.723.1, G.726, G.729ab, VAD, iLBC
Lines quantity	16 lines
Phonebook capacity	1000 entries
Number of VoIP accounts	16
Operating temperature (T-T)	-10 - 50 °C
Operating relative humidity (H-H)	10 - 95 %
Display diagonal	4.3 \
Display resolution	480 x 272 pixels
AC adapter input voltage	100 - 240 V
AC adapter output current	2 A
AC adapter output voltage	5 V
Dual-Tone Multi-Frequency (DTMF) modes	In-band, Out-of band, SIP info
Volume control	Digital
Number of programmable keys	10
USB 2.0 ports quantity	1
Ethernet LAN (RJ-45) ports	2
Networking standards	IEEE 802.3af
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet LAN interface type	Gigabit Ethernet
Supported network protocols	SIP v1, SIP v2, LLDP/CDP/DHCP, OpenVPN, IEEE802.1X, IPv6, FTP/TFTP/HTTP/HTTPS
Harmonized System (HS) code	85171800

Weight and Dimensions

Depth	213 mm
Width	244 mm
Height	185 mm
Package depth	255 mm
Package width	274 mm
Package height	128 mm