Yealink SIP-T46S Administrator's Guide

Call Features
368
3-DNS-NAPTR
Default
0
Parameter
dialplan.emergency.X.value
[2]
<y0000000000xx>.cfg
Description
It configures the emergency number to use on your phones so a caller can contact emergency ser-
vices in the local area when required.
Note: It works only if “dialplan.emergency.enable” is set to 1 (Enabled) and “dial-
plan.emergency.asserted_id_source” is not set to HELD.
Permitted
Values
Number or SIP URI
Default
When X = 1, the default value is 911;
When X = 2-255, the default value is Blank.
Parameter
dialplan.emergency.X.server_priority
[2]
<y0000000000xx>.cfg
Description
It configures the priority of which the emergency servers to be used first.
Multiple values are separated by commas. The servers to be used in the order listed (left to right).
The IP phone tries to make emergency calls using the emergency server with higher priority, and then
with lower priority. The IP phone tries to send the INVITE request to each emergency server three
times.
Note: If the account information has been configured (no matter whether the account registration suc-
ceeds or fails), the emergency calls will be dialed using the following priority: SIP server > emergency
server; if not, the emergency server will be used. It works only if “dialplan.emergency.enable” is set to
1 (Enabled). And “dialplan.emergency.asserted_id_source” is not set to HELD.
Permitted
Values
a combination of digits 1, 2 and 3
Default
1, 2, 3
Parameter
dialplan.emergency.held.server_url <y0000000000xx>.cfg
Description
It configures the primary Location Information Server URL for the phone to send HELD location
request.
Note: It works only if “dialplan.emergency.enable” is set to 1 (Enabled) and “dial-
plan.emergency.asserted_id_source” is set to HELD.
Permitted
Values
String
Default
Blank
Parameter
dialplan.emergency.held.secondary.server_url <y0000000000xx>.cfg
Description
It configures the secondary Location Information Server URL for the phone to send HELD location
request.
Note: It works only if “dialplan.emergency.enable” is set to 1 (Enabled) and “dial-
plan.emergency.asserted_id_source” is set to HELD.
Permitted
Values
String
Default
Blank
Supported
Devices
All phones except T48G, T46G, T42G, T41P and T29G
Parameter
dialplan.emergency.held.request_type <y0000000000xx>.cfg

Yealink SIP-T46S Specifications

General

Manual	Yes
Cables included	LAN (RJ-45)
Number of handles included	1 pc(s)
Mounting	Desk/Wall
Handset type	Wired handset
Product type	IP Phone
Product color	Black
Voice codecs	CNG, G.711Mu, G.711a, G.722, G.723.1, G.726, G.729ab, VAD, iLBC
Lines quantity	16 lines
Phonebook capacity	1000 entries
Number of VoIP accounts	16
Operating temperature (T-T)	-10 - 50 °C
Operating relative humidity (H-H)	10 - 95 %
Display diagonal	4.3 \
Display resolution	480 x 272 pixels
AC adapter input voltage	100 - 240 V
AC adapter output current	2 A
AC adapter output voltage	5 V
Dual-Tone Multi-Frequency (DTMF) modes	In-band, Out-of band, SIP info
Volume control	Digital
Number of programmable keys	10
USB 2.0 ports quantity	1
Ethernet LAN (RJ-45) ports	2
Networking standards	IEEE 802.3af
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet LAN interface type	Gigabit Ethernet
Supported network protocols	SIP v1, SIP v2, LLDP/CDP/DHCP, OpenVPN, IEEE802.1X, IPv6, FTP/TFTP/HTTP/HTTPS
Harmonized System (HS) code	85171800

Weight and Dimensions

Depth	213 mm
Width	244 mm
Height	185 mm
Package depth	255 mm
Package width	274 mm
Package height	128 mm