EL3060 CONTINUOUS GAS ANALYZERS | OI/EL3060-EN REV. A 141
Index
A
Acknowledgement • 130
Active component selection • 53, 77, 91
Alarm value configuration • 53, 59, 89
Analog outputs • 39, 95, 124
Analyzer data sheet • 17, 31, 33, 41, 70, 73, 75, 79,
121, 138
Assembly • 35
Automatic calibration
Control • 48, 53, 58, 62, 130
Manual start • 53, 62, 66
Settings • 53, 58, 61, 63, 67
C
Caldos25
Notes on calibration • 65, 67, 70, 79
Caldos27
Changing the range limits • 80, 88
Configuration and calibration of sample
components • 94
Notes on calibration • 65, 67, 70, 77
Single-point calibration • 77
Standard gas • 77
Calibrating the gas analyzer • 47, 58
Calibration
Automatic calibration • 63, 66
Calibration reset • 119
Manual calibration • 67
Measuring calibration cell (Uras26) • 120
Test gases • 24, 60, 61
Calibration control • 58
Carrying out a calibration reset • 53, 119
Case purging • 27
CD-ROM • 53
Changing the physical unit of a sample
component • 93
Checking the installation • 7, 44, 116
Checking the seal integrity of the gas feed paths
• 7, 34, 116, 117, 137
Commissioning • 44, 47
Communication between the gas analyzer and
the computer • 54
Configuration of signal inputs and outputs (I/O
connections) • 40, 41, 53, 58, 64, 95, 130
Configuration of the Ethernet connection • 53, 96
Configurator • 61, 90, 95
Configuring the gas analyzer • 7, 47, 80
Configuring the language of the user interface •
98, 99
Configuring the QAL3 monitoring • 107, 110
Connect
Electrical cables • 38, 43
Gas lines • 36
Connecting the electrical leads • 7, 43
Connecting the electrical leads – Safety
information • 38
Connecting the gas lines • 7, 36
Connections
Electrical connections • 39
Gas connections • 28, 30, 36
Control charts • 107, 108, 112, 114
Current outputs • 39, 95
D
Description of the gas analyzer • 14
Device information • 53, 127
Device test • 124
Digital inputs/outputs • 39, 95, 124
Dimensions and gas connections of the
EL3060-CU control unit • 28, 35, 36
Dimensions and gas connections of the
EL3060-Uras26 analyzer unit • 30, 35, 36
Display – Measuring mode • 48, 50, 51
Display test • 124
Displaying and printing the control chart • 112, 113
Disposal • 140
Drift reading • 53, 121, 137
Dynamic QR Code • 128
E
Editing or deleting QAL3 values • 113
Electrical connections • 29, 39, 60, 62, 83, 89, 92,
95, 125, 126
Electrical safety • 14, 19
Equipotential bonding • 38, 43
Explosion protection • 11
Exporting or deleting QAL3 data • 110, 114
Externally controlled sample component
switch-over • 92
F
Filter (linear, non-linear) • 90
Flow meter • 18, 36
G
Grounding conductor • 9, 43
Guideline for installation and commissioning • 7
I
I/O connections • 95
I/O modules • 39
I/O test • 124
Information for the installation, maintenance and
repair of electrical installations in hazardous
areas • 11, 15
Information on the concept of operation • 13, 41,
53, 55, 62, 63, 89, 90, 93, 94, 95, 96, 102
Initial purging of gas feed paths • 7, 37, 46
Inspection • 116
Inspection and maintenance • 115