ABB REB670 Series - Page 13

12.1.3.1 Single circuit breaker with single busbar..........................................................................255
12.1.3.2 Single circuit breaker with double busbar, external voltage selection....................... 255
12.1.3.3 Single circuit breaker with double busbar, internal voltage selection........................256
12.1.3.4 Double circuit breaker...........................................................................................................256
12.1.3.5 1 1/2 circuit breaker............................................................................................................... 257
12.1.4 Setting guidelines..................................................................................................................... 259
12.2 Autorecloser for 1 phase, 2 phase and/or 3 phase operation SMBRREC ...........................263
12.2.1 Identification..............................................................................................................................264
12.2.2 Application..................................................................................................................................264
12.2.2.1 Auto reclosing operation Off and On.................................................................................267
12.2.2.2 Start auto reclosing and conditions for start of a reclosing cycle...............................267
12.2.2.3 Start auto reclosing from circuit breaker open information........................................ 268
12.2.2.4 Blocking of the auto recloser...............................................................................................268
12.2.2.5 Control of the auto reclosing dead time for shot 1........................................................ 268
12.2.2.6 Long trip signal...................................................................................................................... 268
12.2.2.7 Maximum number of reclosing shots................................................................................ 269
12.2.2.8 ARMode = 3ph, (normal setting for a three-phase shot)............................................... 269
12.2.2.9 ARMode = 1/2/3ph .................................................................................................................269
12.2.2.10 ARMode = 1/2ph , 1-phase or 2-phase reclosing in the first shot................................. 269
12.2.2.11 ARMode = 1ph+1*2ph, 1-phase or 2-phase reclosing in the first shot......................... 270
12.2.2.12 ARMode = 1/2ph + 1*3ph, 1-phase, 2-phase or 3-phase reclosing in the first shot...270
12.2.2.13 ARMode = 1ph + 1*2/3ph, 1-phase, 2-phase or 3-phase reclosing in the first shot...270
12.2.2.14 External selection of auto reclosing mode........................................................................271
12.2.2.15 Auto reclosing reclaim timer................................................................................................ 271
12.2.2.16 Pulsing of the circuit breaker closing command and counter.......................................271
12.2.2.17 Transient fault.........................................................................................................................271
12.2.2.18 Permanent fault and reclosing unsuccessful signal........................................................ 271
12.2.2.19 Lock-out initiation..................................................................................................................272
12.2.2.20 Evolving fault...........................................................................................................................273
12.2.2.21 Automatic continuation of the auto reclosing sequence.............................................. 273
12.2.2.22 Thermal overload protection holding the auto recloser back.......................................273
12.2.3 Setting guidelines..................................................................................................................... 274
12.2.3.1 Configuration..........................................................................................................................274
12.2.3.2 Auto recloser settings........................................................................................................... 281
12.3 Apparatus control..........................................................................................................................284
12.3.1 Application..................................................................................................................................284
12.3.2 Bay control QCBAY....................................................................................................................288
12.3.3 Switch controller SCSWI...........................................................................................................289
12.3.4 Switches SXCBR/SXSWI...........................................................................................................290
12.3.5 Proxy for signals from switching device via GOOSE XLNPROXY.....................................290
12.3.6 Reservation function (QCRSV and RESIN)............................................................................ 292
12.3.7 Interaction between modules.................................................................................................294
12.3.8 Setting guidelines..................................................................................................................... 296
12.3.8.1 Bay control (QCBAY)..............................................................................................................296
12.3.8.2 Switch controller (SCSWI).....................................................................................................297
12.3.8.3 Switch (SXCBR/SXSWI).........................................................................................................298
Table of contents
Busbar protection REB670 7
Application manual