ABB REB670 Series

To Next Page

To Previous Page

Document ID: 1MRK 505 370-UEN

Issued: November 2018

Revision: D

Product version: 2.2

Main Page

Table of contents7
Introduction23
- This manual23
- Intended audience23
- Product documentation24
- Document symbols and conventions26
  - Symbols26
  - Document conventions27
- IEC 61850 edition 1 / edition 2 mapping27
Application35
- General IED application35
- Main protection functions38
- Back-up protection functions39
- Control and monitoring functions40
- Communication49
- Basic IED functions51
Configuration53
- Description of configuration REB67053
Analog inputs65
- Introduction65
- Setting guidelines65
Local HMI89
- Display90
- LEDs91
- Keypad92
- Local HMI functionality94
Differential protection97
- Busbar differential protection97
Current protection149
- Directional phase overcurrent protection, four steps OC4PTOC149
- Four step single phase overcurrent protection PH4SPTOC158
- Directional residual overcurrent protection, four steps EF4PTOC165
  - Identification166
  - Setting guidelines166
- Four step directional negative phase sequence overcurrent protection NS4PTOC171
- Thermal overload protection, two time constants TRPTTR176
- Breaker failure protection CCRBRF181
- Breaker failure protection, single phase version CCSRBRF189
- Directional underpower protection GUPPDUP197
- Directional overpower protection GOPPDOP202
- Capacitor bank protection CBPGAPC207
Voltage protection213
- Two step undervoltage protection UV2PTUV213
  - Identification213
  - Setting guidelines213
- Two step overvoltage protection OV2PTOV215
- Two step residual overvoltage protection ROV2PTOV218
- Voltage differential protection VDCPTOV223
- Loss of voltage check LOVPTUV225
Frequency protection227
- Underfrequency protection SAPTUF227
- Overfrequency protection SAPTOF228
- Rate-of-change of frequency protection SAPFRC229
Multipurpose protection231
- General current and voltage protection CVGAPC231
Secondary system supervision245
- Fuse failure supervision FUFSPVC245
- Fuse failure supervision VDSPVC248
- Voltage based delta supervision DELVSPVC250
- Current based delta supervision DELISPVC252
- Delta supervision of real input DELSPVC254
Control255
- Synchrocheck, energizing check, and synchronizing SESRSYN255
- Autorecloser for 1 phase, 2 phase and/or 3 phase operation SMBRREC269
- Apparatus control290
- Interlocking305
- Logic rotating switch for function selection and LHMI presentation SLGAPC336
- Selector mini switch VSGAPC337
- Generic communication function for Double Point indication DPGAPC338
- Single point generic control 8 signals SPC8GAPC339
- AutomationBits, command function for DNP3.0 AUTOBITS339
- Single command, 16 signals SINGLECMD340
Logic343
- Trip matrix logic TMAGAPC343
- Logic for group alarm ALMCALH343
- Logic for group alarm WRNCALH344
  - Identification344
    - Application344
    - Setting guidelines344
- Logic for group indication INDCALH344
  - Identification344
    - Application344
    - Setting guidelines345
- Configurable logic blocks345
  - Application345
  - Setting guidelines345
    - Configuration345
- Fixed signal function block FXDSIGN346
  - Identification346
  - Application347
- Boolean 16 to Integer conversion B16I348
  - Identification348
  - Application348
- Boolean to integer conversion with logical node representation, 16 bit BTIGAPC349
  - Identification349
  - Application349
- Integer to Boolean 16 conversion IB16350
  - Identification350
  - Application350
- Integer to Boolean conversion for six-zone busbar BCTZCONN351
  - Identification351
  - Application351
- Integer to Boolean 16 conversion with logic node representation ITBGAPC352
  - Identification352
  - Application353
- Elapsed time integrator with limit transgression and overflow supervision TEIGAPC353
- Comparator for integer inputs - INTCOMP354
- Comparator for real inputs - REALCOMP355
Monitoring359
- Measurement359
- Gas medium supervision SSIMG369
- Liquid medium supervision SSIML370
- Breaker monitoring SSCBR371
- Event function EVENT375
- Disturbance report DRPRDRE376
- Logical signal status report BINSTATREP382
- Limit counter L4UFCNT383
- Running hour-meter TEILGAPC383
- Current harmonic monitoring CHMMHAI384
- Voltage harmonic monitoring VHMMHAI386
Metering389
- Pulse-counter logic PCFCNT389
- Function for energy calculation and demand handling ETPMMTR390
Ethernet-based communication393
- Access point393
  - Application393
  - Setting guidelines393
- Redundant communication394
- Merging unit396
  - Application396
  - Setting guidelines397
- Routes397
  - Application397
  - Setting guidelines397
Station communication399
- Communication protocols399
- IEC 61850-8-1 communication protocol399
- IEC/UCA 61850-9-2LE communication protocol402
- LON communication protocol414
  - Application414
  - MULTICMDRCV and MULTICMDSND416
- SPA communication protocol416
  - Application416
  - Setting guidelines417
- IEC 60870-5-103 communication protocol418
- DNP3 Communication protocol424
  - Application424
Remote communication425
- Binary signal transfer425
Security433
- Authority status ATHSTAT433
  - Application433
- Self supervision with internal event list INTERRSIG433
  - Application433
- Change lock CHNGLCK434
  - Application434
- Denial of service SCHLCCH/RCHLCCH435
  - Application435
  - Setting guidelines435
Basic IED functions437
- IED identifiers TERMINALID437
  - Application437
- Product information PRODINF437
  - Application437
  - Factory defined settings437
- Measured value expander block RANGE_XP438
- Parameter setting groups439
  - Application439
  - Setting guidelines439
- Rated system frequency PRIMVAL439
- Summation block 3 phase 3PHSUM440
  - Application440
  - Setting guidelines440
- Global base values GBASVAL440
- Signal matrix for binary inputs SMBI441
  - Application441
  - Setting guidelines441
- Signal matrix for binary outputs SMBO441
  - Application441
  - Setting guidelines442
- Signal matrix for mA inputs SMMI442
  - Application442
  - Setting guidelines442
- Signal matrix for analog inputs SMAI442
- Test mode functionality TESTMODE447
  - Application447
    - IEC 61850 protocol test mode448
  - Setting guidelines449
- Time synchronization TIMESYNCHGEN449
  - Application449
  - Setting guidelines450
Requirements455
- Current transformer requirements455
- Voltage transformer requirements462
- SNTP server requirements463
- PTP requirements463
- Sample specification of communication requirements for the protection and control terminals in digital telecommunication networks463
- IEC/UCA 61850-9-2LE Merging unit requirements464
Glossary467

ABB REB670 Series - Page 3

Table of Contents

Related product manuals