ABB SCK User Manual (English)

Other manuals for ABB SCK

Questions and Answers:

A
aimee76Sep 1, 2025
What to do if there is danger due to harmful anti-freeze with ABB SCK Industrial Equipment?
- M
  Michael TaylorSep 1, 2025
  To protect yourself from harmful anti-freeze, avoid contact with the cooling water and the anti-freeze. Immediately wash any cooling water or anti-freeze off the skin with soap and water. If cooling water or anti-freeze gets in the eyes despite wearing protective glasses, rinse them thoroughly under running water while holding the eyelids open. Also, follow the instructions in the anti-freeze manufacturer's safety data sheet.
R
Raymond HernandezAug 31, 2025
What to do if there is a risk of scalding due to hot cooling water with ABB Industrial Equipment?
- J
  jallenAug 31, 2025
  To avoid scalding from hot cooling water, do not work on the cooling water circuit until the gas sampling system has cooled down.
J
Jennifer WelchAug 30, 2025
What to do if there is a risk of crushing due to moving gas sampling probe in ABB Industrial Equipment?
- C
  Courtney CarterAug 30, 2025
  To prevent crushing from a moving gas sampling probe, press the service switch before working on the gas sampling system. Additionally, press the EMERGENCY-STOP switch before working on the retractor. Avoid the danger area around the retractor until it is at a standstill, and the warning lamps and buzzer are off. Never stand in the danger area when the protective installation is closed. If the warning lamps light up or the buzzer sounds, immediately leave the danger area, as the probe is about to move. Press the EMERGENCY-STOP switch if anyone is still in the danger area after the warnings activate.
A
anthonysmithAug 28, 2025
What to do if there is a risk of burning due to falling or spalling material with ABB SCK?
- M
  Megan MorseAug 28, 2025
  To prevent burns from falling or spalling material, never enter the danger area around the retractor during operation. Do not approach the retracted probe until it has cooled down. If approaching the hot probe is unavoidable, wear a face mask against heat, heat-proof gloves, and protective welder's clothing.
P
Phillip RamirezAug 27, 2025
What to do if there is a risk of crushing by heavy transport units with ABB SCK?
- J
  jonesmargaretAug 27, 2025
  To avoid crushing by heavy transport units, ensure that only appropriately trained personnel transport the units using recommended equipment. Do not stand under suspended loads, and carefully follow the transport instructions provided in these operating instructions.
A
Angela WoodAug 26, 2025
How to handle danger due to harmful gases and jet flames with ABB Industrial Equipment?
- K
  Kimberly HowellAug 26, 2025
  To manage the danger from harmful gases and jet flames, make sure the workplace is adequately ventilated. Only enter the danger area around the retractor when the shutter is closed. If indicated, lock the shutter before starting work. If working near the duct opening is unavoidable, wear respiratory protection.
P
paula94Aug 25, 2025
What to do if there is a risk of burning due to hot surfaces on ABB SCK?
- X
  xloweAug 26, 2025
  To prevent burns from hot surfaces, avoid touching the gas sampling system during and after operation. Allow the system to cool down to less than 50 °C before touching it. If touching it during operation is unavoidable, wear a face mask against heat, heat-proof gloves, and protective welder's clothing.
H
Heather CohenAug 23, 2025
How to prevent mechanical, thermal, and material dangers with ABB Industrial Equipment?
- P
  Paul ZavalaAug 25, 2025
  To avoid mechanical, thermal, and material dangers from moving or falling parts, hot surfaces, hot cooling water, anti-freeze, compressed air, or lubricating oil, wear appropriate personal protective equipment. This includes closed overalls with long sleeves and trousers, safety shoes, safety gloves suitable for mechanical work, safety glasses, and a protective helmet. Additional protective equipment may be required as prescribed by the operator.