ADCMT 8230E - Connection Diagram for Sensors

114 pages

To Next Page

To Previous Page

8230E Optical Power Meter Operation Manual

1.4 Connectable Sensors

1-5

Figure 1-1 Connection Diagram for Sensors

8230E OPTICAL POWER METER

82311B OPTICAL SENSOR

82313B OPTICAL SENSOR

Main Page

Table of Contents11
Introduction19
Product Outline19
Standard Accessory19
Standard Accessories19
Accessories20
Connectable Sensors21
Old and New Model Numbers of Optical Sensors22
Connection Diagram for Sensors23
Optical Power Meter Software Revisions and Applicable Optical Sensors24
List of Software Revisions Required for Optical Sensor Operations24
Options and Accessories25
Option to Use Old-Type Sensors (OPT8230E+70)25
Sensor Option25
Operating Environment26
Battery26
How to Remove and Replace Batteries27
Battery Cover27
Battery Alignment27
Precautions When Using this Instrument28
1.10 Checking Operations28
1.11 Cleaning29
Cleaning the 8230E29
Cleaning the Incident Surface of the Sensor29
1.12 How to Store and Transport the Instrument29
Storage29
Transportation29
1.13 Warm-Up30
1.14 Calibration30
1.15 Replacing Parts with Limited Life30
1.16 Product Disposal and Recycle31
Panel and Function Description33
Front Side33
Function Description33
Front View33
2.1.2 Display Description37
Battery Indicator37
Rear Side38
Rear View38
Upper Side39
Bottom Side39
Top View39
Bottom View39
How to Perform Measurements41
Menu Map41
Menu Description42
Measurement Procedure43
Connecting the Sensor43
Setting the Wavelength43
Zero Cancel43
Setting the Range43
Reading the Display43
Backing up and Initializing the Setting Parameter44
Backing up the Setting Parameter44
Initial Values of the Parameters and Backup44
3.4.2 How to Initialize45
Outline of the Parameter Backup45
Wavelength Preset46
Setting the Preset Wavelength46
Setting the Preset Wavelength47
Calling the Preset Wavelength48
Remote Controlling Via Usb49
Outline49
USB Specifications49
Setting up the USB Port49
Driver for Control49
Connecting to a Personal Computer50
Setting the MYID50
Response to the *IDN? Command50
Measurement Data Output Format52
Status Register56
Status Register Structure56
Status Byte Register57
Device Event Status Register58
Standard Event Status Register59
Error Register60
How to Set the Remote Command61
Linking a Header to an Argument61
Command Separator62
Command Terminator62
Executing Commands62
Remote Control Command List63
Initial Value63
Availability63
Remote Control Commands63
4.7 Sample Programs70
Program Example 170
Measurement Image70
Display71
Program Example 272
Measurement Image72
Technical Notes75
Principle of Measurement75
Block Diagram76
Optical Power Calibration and Wavelength Sensitivity Correction77
Wavelength Sensitivity Characteristics and Power Calibration of the Sensor77
Analog out78
Relationship between the Current Range and the Output Voltage at Analog Output78
Performance Test79
Performance Test for the 8230E79
Cable and Adapters Required for Performance Test79
Instruments Required for Current Measurement Calibration and Performance79
6.1.1 How to Connect Instruments80
How to Test the Performance80
Connection Diagram for Performance Test80
Current Range Accuracy Specifications81
Measuring Instruments and Other Equipment Required to Check the Performance of the Optical Sensor83
Equipment Required for Evaluating Optical Sensors83
How to Connect the Instrument84
Test Point and Judgment Criteria84
Connection Diagram for the Optical Sensor Performance Test84
Judgment Criteria for the Optical Sensor84
Test Procedure85
Calibration87
Measuring Instrument, Cable, and Other Instruments Required for Calibration87
Cables, Adapters, and Others Required for Calibration87
Precautions88
How to Connect the Instrument89
Connection Diagram for the IV Offset Calibration89
Connection Diagram for the Current Measurement Calibration89
Current Measurement Calibration Point and Its Allowable Range90
Current Measurement Calibration90
Calibration Point and Its Allowable Range90
Calibration Operation91
Calibration Flow91
Current Measurement Calibration Flow93
Calibration Procedure94
Offset Calibration94
Current Measurement Calibration94
Specifications97
8230E Specifications97
Instrument Specifications97
General Specifications99
Standard Accessories99
Optical Sensor Specifications100
Sensor Specifications (Sold Separately)100
Wavelength Sensitivity Correction Option and Additional Calibration Wavelength Option102
Appendix103
Trouble Shooting (before Asking for Repair103
Problem and Solution103
A.2 Error Messages104
Error Message104
Causes of the Generated Calibration Errors105
8230E Dimensional Outline Drawing107

ADCMT 8230E - Connection Diagram for Sensors

Table of Contents

Related product manuals