Allen-Bradley 1336 PLUS Troubleshoot Manual

2–9Troubleshooting and Error Codes
Publication 1336 IMPACT-6.2 – March 1998
Fault Code and
Text
Suggested ActionDescription
Fault
Type
LED Information
06042
SP 2 Timeout
VP, Flashing red Soft
The SCANport adapter at port 2 has been
disconnected and the logic mask bit for
port 2 is set (1).
If the adapter was not intentionally
disconnected:
• Check the wiring to the SCANport adapters.
• Replace wiring, SCANport expander,
SCANport adapters, and main control board.
• Replace drive, if required.
If you do not want this condition to be
reported as a fault, change bit 10 in Fault
Select 1 (parameter 20) to 0.
06043
SP 3 Timeout
VP, Flashing red Soft
The SCANport adapter at port 3 has been
disconnected and the logic mask bit for
port 3 is set (1).
If the adapter was not intentionally
disconnected:
• Check the wiring to the SCANport adapters.
• Replace wiring, SCANport expander,
SCANport adapters, and main control board.
• Replace drive, if required.
If you do not want this condition to be
reported as a fault, change bit 11 in Fault
Select 1 (parameter 20) to 0.
06044
SP 4 Timeout
VP, Flashing red Soft
The SCANport adapter at port 4 has been
disconnected and the logic mask bit for
port 4 is set (1).
If the adapter was not intentionally
disconnected:
• Check the wiring to the SCANport adapters.
• Replace wiring, SCANport expander,
SCANport adapters, and main control board.
• Replace drive, if required.
If you do not want this condition to be
reported as a fault, change bit 12 in Fault
Select 1 (parameter 20) to 0.
06045
SP 5 Timeout
VP, Flashing red Soft
The SCANport adapter at port 5 has been
disconnected and the logic mask bit for
port 5 is set (1).
If the adapter was not intentionally
disconnected:
• Check the wiring to the SCANport adapters.
• Replace wiring, SCANport expander,
SCANport adapters, and main control board.
• Replace drive, if required.
If you do not want this condition to be
reported as a fault, change bit 13 in Fault
Select 1 (parameter 20) to 0.
06046
SP 6 Timeout
VP, Flashing red Soft
The SCANport adapter at port 6 has been
disconnected and the logic mask bit for
port 6 is set (1).
If the adapter was not intentionally
disconnected:
• Check the wiring to the SCANport adapters.
• Replace wiring, SCANport expander,
SCANport adapters, and main control board.
• Replace drive, if required.
If you do not want this condition to be
reported as a fault, change bit 14 in Fault
Select 1 (parameter 20) to 0.
06047
SP Error
VP, Flashing red Soft
SCANport communications have been
interrupted.
If the adapter was not intentionally
disconnected:
• Check the amount of noise on the system.
• Check the wiring to the SCANport adapters.
• Replace wiring, SCANport expander,
SCANport adapters, and main control board.
• Replace drive, if required.
If you do not want this condition to be
reported as a fault, change bit 15 in Fault
Select 1 (parameter 20) to 0.

Allen-Bradley 1336 PLUS Specifications

General

Input Voltage	200-240VAC, 380-480VAC, 500-600VAC
Output Frequency	0-400 Hz
Frequency	50/60 Hz
Dimensions	Varies by model
Weight	Varies by model
Enclosure	NEMA 1
Output Current	Varies by model
Power Rating	Varies by model
Communication	RS-485
Protection Features	Overcurrent, Overvoltage, Undervoltage, Overtemperature, Short Circuit
Storage Temperature	-40 to 70°C (-40 to 158°F)
Humidity	5 to 95% non-condensing
Control Method	Sensorless Vector