6 Rockwell Automation Publication 1788-UM059B-EN-P - August 2015
Table of Contents
Chapter 3
Install the 1788-EN2DNR Linking
Device
Environmental and Enclosure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
European Hazardous Location Approval . . . . . . . . . . . . . . . . . . . . . . . 30
North American Hazardous Location Approval. . . . . . . . . . . . . . . . . 30
Certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Required Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Required Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Connect the 1788-EN2DNR Linking Device to the EtherNet/IP
Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Connect the 1788-EN2DNR Linking Device to the DeviceNet Network
35
Set the DeviceNet Node Address and Baud Rate . . . . . . . . . . . . . . . . . . . . 36
Set the DeviceNet Node Address and Baud Rate by Using the
Rotary Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Set the DeviceNet Node Address and Baud Rate by Using
RSNetWorx for DeviceNet Software . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Set the Linking Device IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Set the Linking Device IP Address by Using the Rotary Switches . 37
Set the Linking Device IP Address by Using DHCP/BOOTP. . . . 38
Set the Linking Device IP Address by Using RSLinx Software . . . . 40
Set the Linking Device IP Address by Using the Linking Device
Web Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Configure the Driver in RSLinx Software. . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Register the EDS File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Chapter 4
Configure the Linking Device
RSNetWorx for DeviceNet Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Set the DeviceNet Node Address and Baud Rate . . . . . . . . . . . . . . . . 46
Enable/Disable Autobaud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Configure DeviceNet I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Studio 5000 Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Add the Linking Device to a Studio 5000 Logix Designer Application
54
Configure the Linking Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Assembly Objects and Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Chapter 5
USB Cable
Connect via USB to the Linking Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Configure the USB Driver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60