Bender ISOMETER iso685-D-P User Manual

SettingsSettings
iso685-D-P_D00170_00_M_XXDE/06.2016
58
10.1 2.5.2 Current transformer monitoring
Refer to “10.1 2.4.1.2 CT monitoring”.
10.1 2.5.3 Response value I
ΔL
Refer to “10.1 2.4.1.3 I∆L Response value”.
10.1 2.5.4 Response value I
Δn
Refer to “10.1 2.4.1.4 I∆n Response value”.
10.1 2.6 Outputs
In this menu, each output can be configured. Also refer to “10.1 2.4.2 Outputs”.
10.1 2.6.1 Relays
Select the relay that you would like to configure.
...
10.1 2.6.1.1 TEST
Refer to “10.1 2.4.2.1.1 TEST”.
10.1 2.6.1.2 Operating mode
Refer to “10.1 2.4.2.1.2 Operating mode”.
10.1 2.6.1.3 Function 1
Refer to “10.1 2.4.2.1.3 Function 1”.
10.1 2.6.1.4 Function 2
Refer to “10.1 2.4.2.1.3 Function 1”.
10.1 2.6.1.5 Function 3
Refer to “10.1 2.4.2.1.3 Function 1”.
10.1 2.6.2 Buzzer
In this menu, each buzzer can be configured. Also refer to “10.1 2.4.2.2 Buzzer”.
10.1 2.6.2.1 TEST
Refer to “10.1 2.4.2.1.1 TEST”.
10.1 2.6.2.2 Function 1
Refer to “10.1 2.4.2.1.3 Function 1”.
•Relay 1 (BS 2/1)
10.1 2.6.2.3 Function 2
Refer to “10.1 2.4.2.1.3 Function 1”.
10.1 2.6.2.4 Function 3
Refer to “10.1 2.4.2.1.3 Function 1”.
10.1 2.6.3 Digital output
In this menu, each digital output can be configured.
Also refer to “10.1 2.4.2.3 Digital output”.
10.1 2.6.3.1 TEST
Refer to “10.1 2.4.2.3.1 TEST”.
10.1 2.6.3.2 Function 1
Refer to “10.1 2.4.2.1.3 Function 1”.
10.1 2.6.3.3 Function 2
Refer to “10.1 2.4.2.1.3 Function 1”.
10.1 2.6.3.4 Function 3
Refer to “10.1 2.4.2.1.3 Function 1”.
10.1 2.7 Inputs
In this menu, each digital input can be configured. Therefore, select a digital input.
10.1 2.7.1 Mode
Refer to “10.1 2.4.3.1 Mode”.
10.1 2.7.2 t(on)
Refer to“10.1 2.4.3.2 t(on)”.
10.1 2.7.3 t(off)
Refer to “10.1 2.4.3.3 t(off)”.
10.1 2.7.4 Function
Refer to “10.1 2.4.3.4 Function”.
•Dig. input 1 (BS 2/1)
•Dig. input 2 (BS 2/2)

Bender ISOMETER iso685-D-P Specifications

General

Brand	Bender
Model	ISOMETER iso685-D-P
Category	Measuring Instruments
Language	English