Bosch Access Easy Controller 2.1 - Page 129

Bosch Access Easy Controller 2.1

136 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Access Easy Controller 2.1 Appendix G Blank Configuration Form | en 129

Robert Bosch (SEA) Pte Ltd Hardware Installation Manual 2018.11 | 1.0.6 | F.01U.122.796

SW1 Address Settings:

T5-1 to T5-3

T5-4 to T5-6

Prepared By: ______________

Date: ______________

Table of Contents

Default Chapter3
- Table of Contents3
Copyright, Safety and Warranty6
- Copyright Notice6
- Important Safety Notes7
- FCC Information8
Before You Begin9
- General9
- Terminologies9
Overview of Access Easy Controller 2.110
- Architecture of Access Easy Controller 2.110
- Basic Functions in Access Easy Controller11
- Basic Access Easy Controller12
System Layout14
- System Specifications15
The CPU Board18
- Component Layout of the CPU Board20
- Other Components22
4-Reader Board23
- Technical Overview of 4-Reader Board23
- Component Layout of 4-Reader Board23
- Reader Connectors24
- Input Connectors25
- Output Connectors26
- 15 VDC Input Termination28
- Rs23228
- Rs48528
- Tamper and Main Power Fail29
- LED Indicators29
- Reset Button29
- End-Of-Line Setting29
- Address Setting Switch30
- Factory Default Setting30
8-Input-Output Board32
- Technical Overview of 8-Input-Output Board32
- Component Layout of 8-Input-Output Board32
- Input Connectors33
- Output Connectors34
- 15 VDC Input Termination36
- Rs23236
- Rs48537
- Tamper and Main Power Fail37
- LED Indicators37
- Reset Button38
- End-Of-Line Setting38
- Address Setting Switch38
Power Supply Unit40
- Layout of Power Supply Unit40
- Technical Specification of Power Supply Unit with Input Power of 100~240 VAC41
- Power Supply Requirement and Connection41
- Current Consumption42
- Connection in the Main Controller42
Access Easy Extension Unit43
- Upgrading AEC2.1 to Support Additional Four 4-Reader Boards and Four 8-IO Boards45
How to Install Reader and Field Devices47
- HID Miniprox Reader49
- HID Proxpoint Reader50
- HID Proxpro Reader52
- HID Proxpro Reader with Keypad54
- Field Devices Using IO Board56
- Wiring Diagram for Supervised Inputs57
How to Install the Access Easy Controller 2.158
- Preliminary58
- Mounting the Panel on a Concrete Wall58
- Controller Installation60
Card Reader Keypad Functions63
- Keypad Layout63
- Keypad Functions63
- Entry Operation63
- Using Card + PIN Mode on a Keypad Reader63
- Using Keypad in "Enable Keypad Only Operation" Mode64
- Other Usage64
- Changing PIN Code65
- Entry and Arm/Disarm Reader65
Common Alarm Output68
- Overview68
- Alarm (All Input Points)68
- Door Forced Open and Door Held Open68
- Panel AC Failure68
- Controller Tamper69
- Duress69
How to Set up the Access Easy Controller 2.1 and the Computer70
- Overview70
- Configuring a Web Browser to Work with Access Easy Controller71
- Web Browser Set-Up on a Windows Computer71
- Install AEC2.1 Certificate on a Windows Computer78
- How to Set Initial Controller Configuration83
Dial-In Networking85
- Guidelines for Modem Installation - Not Investigated by UL85
- Installing the Modem85
- Modem Switch Settings87
- Dial-In Security Features88
- Controller Setup89
- Handling of IP Addresses by Access Easy Controller 2.189
- Changing the Dial-In IP Address90
- Configuring a Windows Computer to Dial the Access Easy Controller90
- Handling Simultaneous Network and Dial-In Connections95
Restoring a Backup Copy of Database to the Access Easy Controller96
- Tools Needed96
- Before Starting the Update96
- Recovering Controller Database from a Windows Computer96
Entry and Arm/Disarm Reader98
- Wiring Diagram of a HID Compliant Entry and Arm/Disarm Reader100
Appendix A How to Install & Set the TCP/IP Address on a PC101
Appendix B Modem Setup105
- Preparing the WAVECOM GSM Modem for AEC2.1105
- How to Test the GSM Modem106
Appendix C Detailed Wiring108
Appendix D Selecting a Correct Battery Size111
- Battery Specification for Access Easy Controller 2.1111
Appendix E Troubleshooting Login Problems114
- Network Connectivity Problems115
Appendix F Frequently Asked Questions120
- General Questions120
- Controller Questions122
- Reader and Door Questions123
- Inputs and Outputs125
- Network Question125
Appendix G Blank Configuration Form127
Appendix H Resetting to Factory Default130
- Resetting to Factory Default131
- Resetting IP Address to Default IP Address132
Appendix I Ports Used by AEC2.1 and AEMC133

Related product manuals

Preview: Access Modular Controller 2

Access Modular Controller 2

Preview: Bosch ACC MT

Preview: Bosch AMC2

Preview: Bosch AMC-4W

Preview: Bosch AMC2-4W

Preview: Bosch AMC2 Series

Bosch AMC2 Series

Bosch APC-AMC2-4W

Preview: Bosch ADS?AMC2?2WCF

Bosch ADS?AMC2?2WCF

Preview: Bosch APC-AMC2-4WCF

Bosch APC-AMC2-4WCF

Bosch APC-AMC2-4R4CF

Preview: Bosch CR 10

Preview: Bosch 2600 Series

Bosch 2600 Series