Bosch D9068 - 4: RPT STEERING

D9068 | Operation and Installation Guide | 5.0 Programming
44
Bosch Security Systems, Inc. | 3/13 | F01U071094-07
setting appears in parentheses on the
first line.
11.Press [# Command] to verify your
selection. Press [* Clear] to return
to the Phone Control submenu.
Event text is sent only for the
Modem IIIa
2
format, and only
when the serial link to an
analog FACP is used.
4: RPT STEERING
To access RPT STEERING, select
[0]: PROGRAM [5]: PROG ACC’NTS[4]:
RPT STEERING.
You can direct the various classes of
reports to specific phone numbers. The
report classes are:
 Non-supervisory Alarms: Include fire
alarms, water-flow alarms, and
monitor alarms.
 Supervisory Alarms: Come from points
that are configured as supervisory
types.
 Non-supervisory Restorals: Include
fire, water-flow, and monitor
restorals.
 Supervisory Restorals: Come from
points that are configured as
supervisory types.
 Trouble Reports: Include all point
and system troubles and restorals.
The tests include Auto Tests, Manual
Tests, and Off-normal at Test
Reports.
Refer to Appendix E: Report
Routing on page 63 for the
appropriate routing of each
report.
To direct reports to particular
telephone numbers:
1. From the PROG ACC’NTS submenu, press
[4] to select 4: RPT STEERING. The
window shows:
REPORT STEERING
1: NONSUP ALRM
2: SUPVSY ALRM
3: ALM RSTR, RST
4: SUPVSY RSTR
5: TESTS
6: TBL, TBL RSTR
2. Press the number key that corresponds
to your selection. The window that
appears depends on your choice. In
this example, the non-supervisory
alarm is selected. The window shows:
NONSUP ALRM (__)
1- PHONE 1 ONLY
2- PHONE 2 ONLY
3- PHON 1 AND 2
4- PHN 2 BACKUP
The options on this window are:
 PHONE 1 ONLY: Sends the report
only to Phone #1.
 PHONE 2 ONLY: Sends the report
only to Phone #2.
 PHONE 1 AND 2: Sends the report to
Phone #1 and Phone #2.
 PHONE 2 BACKUP: Sends the report
to Phone #1 and then to Phone #2
if Phone #1 fails. The D9068
attempts to send the report to
Phone Number 1 first, and if that
attempt fails, the D9068 sends the
report to Phone Number 2.
3. Press the number key that corresponds
with your selection followed by [#
Command]. Then press
[* Clear] to return to the Report
Steering submenu.
Report Steering menu choices 2
to 6 have the same menu options
as Report Steering 1: NONSUP
ALRM. Use the instructions for
NONSUP ALRM to set Report
Steering Menu choices 2 through
6.
5: LINE CONTROL
Refer to Table 1 on page 4 for
information about settings permitted in
UL864 installations.
To access LINE CONTROL, select [0]:
PROGRAM [5]: PROG ACC’NTS[5]: LINE
CONTROL. This option allows you to set
the dialing type and line supervision
for each telephone line.
To set the dialing type and line
supervision for phone lines:
1. From the Prog Acc’nts submenu, press
[5] to select 5: LINE CONTROL. The
window shows:
LINE CONTROL
1: LINE #1
2: LINE #2
2. Press the number key that corresponds
with the line you want to configure.
The example here is LINE #1. The
window shows:
LINE 1 CONTROL
1: DIALING TYPE
2: MONITOR LINE
3: WAIT DIALTONE