CASE CONSTRUCTION CX37C - Disposal of fluids, lubricants, and spare parts

To Next Page

To Previous Page

6-MAINTENANCE

Disposalofuids,lubricants,andspareparts

Fluids,lubricantsandsparepartsusedonthemachinearenotfullycompatiblewiththeenvironment.Makesureto

carryoutallmaintenanceoperationsusingappropriatetools,inordertoavoidanyriskofdamagingtheenvironment.

NOTE:forexample,makesurethatthereceptacleforcollectingoiltobereplacedisnotleaking.

Neverspreaduidsorlubricantsonthegroundorintowater.ConsulttheCASECONSTRUCTIONdealerortheLocal

EnvironmentalAgencyinordertoobtaininformationonthecorrectmethodofdisposinguidsandlubricantsusedon

themachine.

Neverthrowawaysparepartsasltersorbatteries.ConsulttheCASECONSTRUCTIONdealerortheLocalEnvi-

ronmentalAgencyinordertoobtaininformationonthecorrectmethodofdisposinglters,batteriesorotherspare

partsusedonthemachine.

6-9

Main Page

Table of Contents2
General Information7
Note to the Owner7
Intended Use8
Electro-Magnetic Compatibility (EMC)8
Telematics (Optional)8
Product Identification9
Operator's Manual Storage on the Machine12
Machine Orientation13
Machine Components14
Safety Information17
Signal Word Definitions17
Safety Rules - Utility Precautions18
Safety Rules19
Ecology and Environment28
Hand Signals29
California Proposition 65 Warning33
Safety Signs34
Controls and Instruments53
Access to Operator's Platform53
Door and Steps53
Operator's Seat56
Forward Controls58
Windshield65
Left-Hand Side Controls66
Safety Lock Lever68
Engine Speed Control68
Emergency Exit Hammer69
Windshield Washer Reservoir70
Right-Hand Side Controls71
Dozer Blade Control Lever74
Instrument Cluster75
Air Conditioning Control80
Ventilation and Heating82
Rearward Controls83
Storage Compartment83
Overhead Controls84
Cab Internal Lighting84
Radio85
Exterior Controls94
Side Doors94
Rear View Mirrors96
Battery Disconnect Switch98
Fuel Tank99
Operating Instructions101
Starting the Unit101
Anti-Theft Protection101
Starting the Engine103
Bringing the Machine up to Operating Temperature105
Operating the Machine in Hot or Cold Weather106
Operating the Machine107
Lowering the Attachment in the Event of a Failure111
Bucket Replacement112
Hydraulic Control Lever Operating Pattern113
Caution While Using Rubber Tracks116
Stopping the Unit120
Stopping the Engine120
Moving the Unit121
Machine Travel121
Parking the Unit127
Parking the Machine127
Transport Operations129
Road Transport129
Loading the Machine Onto a Transport Trailer129
Preparing for Road Transport131
Tie Downs for Shipping131
Unloading the Machine from a Transport Trailer132
Shipping Transport133
Handling the Machine133
Recovery Transport135
Towing the Machine135
Maintenance137
General Information137
Basic Instructions137
General Specification - Biodiesel Fuels140
Fluids and Lubricants142
Engine Oil Recommended Operating Temperature Range146
Releasing Pressure in the Hydraulic System147
Fuel System Bleeding149
Protecting the Electronic and Electrical Systems During Battery Charging or Welding150
Maintenance Planning151
Maintenance Chart151
Break-In Period153
Engine Oil and Filter153
Fuel Filter153
Hydraulic Oil Return Filter153
Pilot Line Filter153
Travel Reduction Gears154
Swing Bearing154
Grease Points (Bucket)154
Every 10 Hours155
Engine Oil Level155
Engine Coolant Level156
Hydraulic Oil Level157
Fuel Filter Water Separator158
Fan and Alternator Drive Belt159
Every 50 Hours160
Grease Points (Bucket)160
Grease Points (Boom and Arm)161
Grease Points (Blade)162
Track Tension163
Every 200 Hours165
Fuel Filter Water Separator165
Every 250 Hours167
Battery167
Swing Bearing170
Tightening Torques171
Every 500 Hours172
Engine Oil and Filter172
Fuel Filter174
Fuel Filter Water Separator175
Air Cleaner176
Radiator and Coolers179
Radiator Fan180
Travel Reduction Gears180
Every 1000 Hours181
Hydraulic Oil Return Filter181
Pilot Line Filter182
Travel Reduction Gears183
Every 2000 Hours184
Engine Coolant184
Hydraulic Oil Suction Filter186
Hydraulic Hoses186
Every 5000 Hours187
Hydraulic Oil187
When Necessary189
Bulb Replacement189
Cab Air Filter191
Fuel Tank Drain192
Fuel Tank Strainer193
Control Levers194
Plastic and Resin Parts194
Fuse and Relay Locations195
Fuses195
Storage197
Preparing for Storage197
Periodic Checks198
Starting up the Machine after Storage199
Troubleshooting201
Fault Code Resolution201
Engine - Troubleshooting201
Electrical Systems - Troubleshooting202
Other Systems - Troubleshooting203
Specifications205
Machine Specifications205
Dimensions208
Weights211
Accessories213
Direct Fit Buckets213
Auxiliary Hydraulic Circuits214
Hydraulic Oil - Breaker/Nibbler220
Load Handling221
Thumb Bracket223
Rotating Beacon224

CASE CONSTRUCTION CX37C - Disposal of fluids, lubricants, and spare parts

Table of Contents

Related product manuals