INST.No.INE-868G [DB600] General Instruction Manual
- 160 -
9-2 Parameter list
Item Range Default Setting
O
eration screen
PV (measured value)
to [°C"
:Over-range
:Under-range
SV (setting value)
to [°C" □□□
Step time
to [Hours:Minutes" □□
Output 1 value
to [%"
Output 2 value
to [%"
AUTO/
MANUAL switch
□:AUTO output
:Manual output
□
Event status
:All events OFF
□□to
:All events ON
:Alarm event reset
Timer 1 elapsed time display
to [sec" □□□□
Timer 2 elapsed time display
to [sec" □□□□
CT measured value display
to [A"
:Measured value not obtained
□□
FB measured value
display
to [%" □□□
PID
auto tuning
□□
:Tuning not executed/forced to
terminate
:PID tuning for output 1 started
: PID tuning for output 2 started
:Tuning step 1
□□to
:Tuning step 4
□□
FB tuning
□□
:Tuning not executed/forced to
terminate
:FB tuning started
□□
:FB tuning at zero side
□□
:FB tuning at span side
Pattern repeat remaining
number display
to [times" □□□□
RUN/READY
switch
□□
:RUN status
:READY status
□□
Execution No. selection
for constant value
operation
to □□
Pattern No. selection
to □□
Program drive
:Program operation RESET
□□
:Program operation RUN
□
:Program operation STOP
□□
:Program operation ADVANCE
□□
:Program operation END
MODE0
Executing SV
to [°C" □□□
Executing step time
to [Hours:Minutes" □□
Executing event 1
to
Executing event 2
to
Executing event 3
to
Executing event 4
to
Executing P
:Two-position control
to [%"
□□□
Executing I
to [sec" □□□
Executing D
to [sec" □□□
Executing output limiter L
to [%" □□□
Executing output limiter H
□ to [%" □
Executing guaranty soak
:Function OFF
to [°C"
□□□
MODE1
SV rate of change for rise
:Function OFF
to [°C"
□□□
SV rate of change for fall
:Function OFF
to [°C"
□□□
SV rate of change unit
□
:Seconds
□
:Minutes
:Hours
□□
Constant value operation
PV start
:SV start (PV start OFF)
:PV start
□□□
Alarm action
at READY
:Alarm event not calculated in
READY status
□
:Alarm event calculated in
READYstatus
□□
MODE2
Program/
constant value
operation switch
:
Constant value operation (program operation OFF)
□
:Program operation (program operation ON)
□□□
Program operation
time unit
:[Hours:Minutes"
:[Minutes:Seconds"
□□□
Item Range Default Setting
SV in RESET
to [°C" □□□
Pattern repeat
to [times" □□□□
Operation screen
time display
□
:Step elapsed time
:Step remaining time
□
Pattern clear
□:No pattern clear
:Initialize pattern No. 1
□□to
:Initialize pattern No. 4
□:Initialize all patterns
□□ □□
Pattern copy
□
: No pattern copy
:Copy pattern No.1 to No.2
□□to
: Copy pattern No.4 to No.3
□□ □□
Number of steps
to:No step
to:1 to 12 steps
□□□□
Program operation PV
start
:SV start (PV start OFF)
:PV start
□□□
Start SV
to [°C" □□□
SV for program
operation
to [°C" □□□
Step time
to [H:M, M:S" □□
Execution No.
selection for program
operation
□:Keep the previous No
□to
□□
(STEP1)
□□
(Other than
STEP1)
Output 1
at END
:
Constant value operation (AUTO output)
to [%"
□
Output 2
at END
:
Constant value operation (AUTO output)
to [%"
□
Linked
pattern No.
:No link
:Pattern No.1
□to
:Pattern No.4
□□
MODE3
Grou
No.1
SV for constant value
operation
to [°C" □□□
Event 1
to
Event 2
to
Event 3
to
Event 4
to
P
:Two-position control
to [%"
□□□
I
to [sec" □□□
D
to [sec" □□□
Output limiter L
to [%" □□□
Output limiter H
□ to [%" □
Guaranty soak
:Function OFF
to [°C"
□□□
Grou
No.2
SV for constant value
operation
to [°C" □□□
Event 1
to
Event 2
to
Event 3
to
Event 4
to
P
:Two-position control
to [%"
□□□
I
to [sec" □□□
D
to [sec" □□□
Output limiter L
to [%" □□□
Output limiter H
□ to [%" □
Guaranty soak
:Function OFF
to [°C"
□□□
Grou
No.3
SV for constant value
operation
to [°C" □□□
Event 1
to
Event 2
to
Event 3
to
Event 4
to
P
:Two-position control
to [%"
□□□
I
to [sec" □□□
D
to [sec" □□□
Output limiter L
to [%" □□□
To Next Page
Loading...
